Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Semi gloss Water based finish over satin water based finish

Featured Replies

Pretty sure this is okay, but thought I would ask.

I have three coats of satin Minwax polycrylic on a project, and have run out. I have a full can of semi gloss min wax polycrylic. If I scuff up the surface with some 220, can I apply the semi on top of the satin?

Go for it! As long as the surface is thoroughly scuffed and clean you should be fine. I usually strain my water bourne finishes just to catch any lumps.

I use a grey Scotch Brite pad between coats, or 220 then 320 to smooth out drips , runs or brush strokes. A red abrasive pad is a little rougher if needed, the green kitchen pads are even coarser than the red ones.

Just as the others have said, there won't be any problems.  The only difference between the satin and semi is the amount of flattening agent added :) .  As far as I know it's the same base mixture (before the additives).

 

I typically like to use fine grit paper between coats (400-600) just because water based material seems to cure to a thinner film than other types of finish which can result in a little bit of print through with the scratch marks from sanding.  Like Steve said a scotchbright pad is about perfect IMO..

 

So Pug, the real question is, "What-cha buildin'?" :P

You should be fine, agree with Boatworks, scuff with a higher grit. Whatever your working on, that last coat could get a tish more glossy. So if you want a satin finish, you my have to rub the surface some with 1000 grit.

-Ace-

  • Author

Just as the others have said, there won't be any problems.  The only difference between the satin and semi is the amount of flattening agent added :) .  As far as I know it's the same base mixture (before the additives).

 

I typically like to use fine grit paper between coats (400-600) just because water based material seems to cure to a thinner film than other types of finish which can result in a little bit of print through with the scratch marks from sanding.  Like Steve said a scotchbright pad is about perfect IMO..

 

So Pug, the real question is, "What-cha buildin'?" :P

I'm just finishing up a workbench, and I want to use up some of the cans of finish hanging around the shop. I have 1/2 can of satin water, and almost a full can of semi water. I did the top ( three coats each side) and ran out of the satin. So I figured I could use of the semi and gain a more durable finish to boot. The sheen doesn't really matter too much.

Thank for the advice guys! I always love reading your informative responses. I'll post some pictures soon. I actually have some other projects I have completed that I have been meaning to photograph/post, but just haven't got around to it!

  • 2 months later...

ideally you should build the finish with the glossiest available and then finish with whichever sheen you wish as a topcoat..

ideally you should build the finish with the glossiest available and then finish with whichever sheen you wish as a topcoat..

That has no affect on finish. Semi or satin is nothing more than gloss with flattening agent. Volume of solids is the same.

That has no affect on finish. Semi or satin is nothing more than gloss with flattening agent. Volume of solids is the same.

 

In Marc's Simple Varnish Finish DVD he mentions that the flattening agents in semi or satin can obscure the grain if you build up too many coats, so he recommends doing what dec11ad said as well - building up with gloss and then using whatever sheen you want as your final top coat.  You think that concern is overblown?

 

(I ask because this is relevant to a tabletop that I'll soon be finishing with satin arm r seal).

In Marc's Simple Varnish Finish DVD he mentions that the flattening agents in semi or satin can obscure the grain if you build up too many coats, so he recommends doing what dec11ad said as well - building up with gloss and then using whatever sheen you want as your final top coat.  You think that concern is overblown?

 

(I ask because this is relevant to a tabletop that I'll soon be finishing with satin arm r seal).

 

The flattening agents will shade the overall finish if you sprayed with just one sheen. On the other hand if you sprayed to the manufactures recommended film thickness you wont see much if any difference. If your going for a thick high build you may see some differences depending on the finish  and how thick but its only a personal preference thing. The quantity of solids should not vary from gloss down to satin. The quality of the final finish is not affected.

In Marc's Simple Varnish Finish DVD he mentions that the flattening agents in semi or satin can obscure the grain if you build up too many coats, so he recommends doing what dec11ad said as well - building up with gloss and then using whatever sheen you want as your final top coat.  You think that concern is overblown?

 

(I ask because this is relevant to a tabletop that I'll soon be finishing with satin arm r seal).

 

Yes, I think it's a tish over-blown.

 

You will be fine using say...3 coats of a satin Arm-R-Seal on a table top. No need to buy a can of clear and a can of satin. Save your funds for other things. ;)

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.