Freddie Posted March 21, 2013 Report Posted March 21, 2013 I received my Grizzly G0690 table saw today, very excited. I already inspected the tables myself at the PA warehouse before shipping, so I could skip right to the next steps today. I need to wait for someone to get home to help me put this thing onto the mobile base, so I am going to wait until later to install the extension tables and fence rails. One think I am having trouble with is the belt tensioning. I included a picture. The three belts are all different tensions, and I was having a hard time taking the slack out to even them out. Does anyone have any experience that they can share with me to help this step speed up a bit? Other than that, she's a beaut, am I am a proud papa. Quote
pghmyn Posted March 21, 2013 Report Posted March 21, 2013 Beautiful machine you got there I wish I could help with the blade tensioning, but my saw only had one belt. Quote
Eric. Posted March 21, 2013 Report Posted March 21, 2013 That adjustment should be in your manual. If I remember correctly you just loosen a nut (or two) and push down on the motor until you get the tension you want. I think they recommend like a 1/2" deflection, but I'm almost certain I tightened mine a little more than that...seemed kinda sloppy at 1/2". The process will have to be repeated after it breaks in a few hours. Quote
dwacker Posted March 21, 2013 Report Posted March 21, 2013 Tighten the shortest belt to spec and the rest will be what they are. Run the saw, just fire it up and let it run then reset the tightest belt again. If the belt are alot different than each other then you need better matched belts which are cheap from most autoparts or machinery supply houses. Nice toy have fun. Quote
dcustoms Posted March 21, 2013 Report Posted March 21, 2013 Congrats on the new saw! +1 to what Don said. The belts are just not a matched set. follow the steps above and replace them if they become a problem. Sounds like it may be very minor. Hopefully this new saw won't turn into a 1000 post thread like you jointer purchase... Quote
sjeff70 Posted March 21, 2013 Report Posted March 21, 2013 Freddie the tool man.... I'm interested in how people are moving these things around. Are you using just muscle to get it on a mobile base? If so how many people? How did you get the pallet with saw to the garage? Quote
Freddie Posted March 21, 2013 Author Report Posted March 21, 2013 Jeff i am very strong haha. Thanks guys for the responses. I already loosened the motor bolt and dropped it as far as it could go, and i had decent tension on one belt. The others were wobbly and after a few second test run there was small shards of rubber on the bottom of the cabinet. Ill get back in the shop later and investigate some more. I might pop the table off so i can just put the rest onto the mobile base by myself, shouldnt be too bad. Then i can put it all together. Thanks for the tip on matched belt sets from auto parts stores, i may look into it if the uneven belts turn out to be a hassle Quote
Freddie Posted March 22, 2013 Author Report Posted March 22, 2013 Well I got the saw all put together last night, only thing left to do is the fence adjustments. This saw will be doing alot of cutting today Im excited. Quote
Eric. Posted March 22, 2013 Report Posted March 22, 2013 Looks familiar...only shinier. Hope the UHMW plastic on your fence is flatter than mine. Go rip a board...bet it's not straight. Quote
Freddie Posted March 22, 2013 Author Report Posted March 22, 2013 Thats ok eric im just gonna re mill the plastic Quote
Eric. Posted March 22, 2013 Report Posted March 22, 2013 LOL, okay. It's not actually the plastic...the plastic is flat, I'm quite sure. It's how they bolt it to the steel tube that screws it up. Divets, bowed, ugly. I have to use a plywood auxiliary fence if I need dead-straight cuts for something. Have you tried it yet? Maybe you got lucky. I'll be replacing my fence in the near future. Quote
pghmyn Posted March 22, 2013 Report Posted March 22, 2013 My fence came out pretty good when I put it on the saw. I never really fiddled around with checking the complete accuracy of it (divets). I will go do that now, actually. Freddie, that is a great looking machine. Hope you like it. Quote
Freddie Posted March 22, 2013 Author Report Posted March 22, 2013 Eric, the fence is not too bad, there are slight dips around all the screws, and the plastic dips in right at the beginning by the cam handle. That wont be an issue since there is more than enough reference before the blade. I have been cutting down ply for cabinets today and I took a piece and laid my straight edge on the rip, it was really flat, and both edges parallel so I think everything worked out great in that aspect. One thing I was concerned about was my front fence rail is not square to the table because the angle iron is not 90 degrees. I don't know if this is common or not, but the fence cam does not engage the center of the fence tube, it grabs the top edge since the whole unit sags. Has anyone else dealt with this issue? Quote
Tpt life Posted March 23, 2013 Report Posted March 23, 2013 My Vega Pro fence rail also has a sag that keeps it from being perfectly square to the table. This is slightly mis-stated as the Vega rail is tubular but it is the same issue of mounting hardware that does not keep square to the table top. I think that this might not be as important as the alignment that keeps it perpendicular to the blade plane especially since cuts are successful. Quote
Freddie Posted March 23, 2013 Author Report Posted March 23, 2013 I put this thing to the test today and i could not be happier, so the front rail is a minor issue. With my new plywood blade i got beautiful edges on all my cabinet parts. Great day in the shop today Quote
Eric. Posted March 23, 2013 Report Posted March 23, 2013 Eric, the fence is not too bad, there are slight dips around all the screws, and the plastic dips in right at the beginning by the cam handle. That wont be an issue since there is more than enough reference before the blade. I have been cutting down ply for cabinets today and I took a piece and laid my straight edge on the rip, it was really flat, and both edges parallel so I think everything worked out great in that aspect. One thing I was concerned about was my front fence rail is not square to the table because the angle iron is not 90 degrees. I don't know if this is common or not, but the fence cam does not engage the center of the fence tube, it grabs the top edge since the whole unit sags. Has anyone else dealt with this issue? Good deal! Glad to hear it. You deserve a break after your jointer ordeal. If the cuts are straight and consistent, there is no problem. Yeah? Quote
pghmyn Posted March 23, 2013 Report Posted March 23, 2013 Good deal! Glad to hear it. You deserve a break after your jointer ordeal. If the cuts are straight and consistent, there is no problem. Yeah? Exact same feeling here. That jointer could have left a sour taste in your mouth for Grizzly, but you decided to go back. Brave Quote
Freddie Posted March 23, 2013 Author Report Posted March 23, 2013 I felt confident in staying with them because i was allowed to personally inspect the machine at the warehouse. Compared to my jointer purchase, i was alot more relaxed because i knew exactly what i was receiving quality wise. A few slight things like uneven belts and sagging fence rail, but nothing that stopped production in the shop today. I will say that assembly and setup on the table saw was a breeze. With the wings installed, both sides taper from zero to .005". Blue tape was too thick as they made the tables angle up. I didnt have anything else to shim and i certainly wasnt cutting up my feelers, so i left it. I think its perfectly fine. Quote
knotscott Posted March 23, 2013 Report Posted March 23, 2013 I put this thing to the test today and i could not be happier.... With my new plywood blade i got beautiful edges on all my cabinet parts. Great day in the shop today Sweet! That's what it's all about. Congrats! Quote
CessnaPilotBarry Posted March 23, 2013 Report Posted March 23, 2013 I put this thing to the test today and i could not be happier, so the front rail is a minor issue. With my new plywood blade i got beautiful edges on all my cabinet parts. Great day in the shop today Here's to many years of happiness! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.