Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Composite lumber table?

Featured Replies

My outdoor table is done, and I need to build new one. I was considering using composite lumber for the build. Has anyone tried this? The fact of it being maintenance free is a big plus! Also, there is no finish involved so the build is relatively quick.

My guess is joinery will need to mechanical. Is there other methods or adhesive available?

Ideas? Opinions?

I have seen decks and furniture using treated lumber for the framework and the composite lumber for the surfaces, seats and tabletops.

If you screw from underneath it conceals most of the screws.

Steve's suggestion is the most feasible to me. Trex makes concealed fasteners for their composites.

  • Author

I have seen decks and furniture using treated lumber for the framework and the composite lumber for the surfaces, seats and tabletops.

If you screw from underneath it conceals most of the screws.

I kinda figured this would be the case. Maybe I'll just go with cedar or teak. Any other suggestions on an outdoor construction lumber? This table will be outside all summer and winter, so the conditions will be harsh.

I've heard (but not tested) that the Kreg deck jig works fantastically well on composites.

 

There's also several different types of composites, based off what it will be used for.  Currently, my budget can afford the one called "spare pare of pants."  (I kid about what I can afford, but I know that there are several different types, based off how much moisture it will be exposed to, how much UV rays, how much wear, etc.)

Trex is a durable exterior product.  It is not structural and has substantial movement, but if you allow for that, it will hold up well.  I tried it as solid top on an exterior couch and it was an abysmal failure.  As long as the table you envision uses the same convention as a deck, you be fine.  Figure at least a fat 16 penny framing nail for spacing.  I'd actually go a hair wider for a gap. 

  • Author

Trex is a durable exterior product. It is not structural and has substantial movement, but if you allow for that, it will hold up well. I tried it as solid top on an exterior couch and it was an abysmal failure. As long as the table you envision uses the same convention as a deck, you be fine. Figure at least a fat 16 penny framing nail for spacing. I'd actually go a hair wider for a gap.

Good point. I am planning on building the top with lots of space for rain and snow to drain through. My rough plan is either painted pt lumber with a composite top, or a full hardwood table made of some weather resistant material. In my experience, nothing is truly "weather proof"' and it is a game of how long will the item last. I would like it to be as long as possible, even if the upfront cost is higher.

I am probably not going to finish it at all, as it will be an exercise in frustration every season.

I built a lot of decks. Just know that algae is a concern with textured composites. I do not think this should put you off. We used to bleach soak (10%) and then pressure wash. I just want you to be prepared to clean your finished piece with algae in mind.

  • Author

I built a lot of decks. Just know that algae is a concern with textured composites. I do not think this should put you off. We used to bleach soak (10%) and then pressure wash. I just want you to be prepared to clean your finished piece with algae in mind.

Thanks for the info. I cleaned my deck last year with oxygen bleach to get rid of algae. What a job! My deck smelled like an old wharf by the sea! I didn't realize that composite had this issue.

i built a 7' long table for my " Big Green Egg " grills. I have 2, a big new one and an old original one. I made the table out of teak in 1995 ,8/4 frame and legs with a 4/4 top. All the top boards are screwed from underneath with brass screws and spaced about an 1/8 apart. All the frame and leg joints were also just screwed. 18 years out in the weather has turned it a nice silver patina with no other signs of decay. I used up the leftover teak i had hoarded from 3 different jobs. I figured it was worth $750 in materials back then but it has served me well with no maintenance at all. 

if you use plantation grown teak for the top and legs you could probably save some $ and use cypress or something for the framework.

A buddy of mine made a patio table from ironwood.  Hell on blades, but still looks good after 3 years with only an application of teak oil.

  • Author

i built a 7' long table for my " Big Green Egg " grills. I have 2, a big new one and an old original one. I made the table out of teak in 1995 ,8/4 frame and legs with a 4/4 top. All the top boards are screwed from underneath with brass screws and spaced about an 1/8 apart. All the frame and leg joints were also just screwed. 18 years out in the weather has turned it a nice silver patina with no other signs of decay. I used up the leftover teak i had hoarded from 3 different jobs. I figured it was worth $750 in materials back then but it has served me well with no maintenance at all. 

if you use plantation grown teak for the top and legs you could probably save some $ and use cypress or something for the framework.

Yes, teak is quite pricey here. It comes in at about 17.50 bf. my table would cost about 500 dollars, which is too expensive.

  • Author

A buddy of mine made a patio table from ironwood. Hell on blades, but still looks good after 3 years with only an application of teak oil.

I don't think iron wood is available in my area. Does it have another common name?

I don't think iron wood is available in my area. Does it have another common name?

I believe it's the same thing as Ipe.  A friend of mine did his entire wrap around deck in ironwood.  Went through 5 chop saw blades.  He built the seat in his steam room with it, too.  He didn't want ceramic to sit on.

I don't know if it's available in Ontario, but you can also look for Black Locust - it's often used as a substitute for pressure treated lumber, apparently. Easy to cut, a pain to nail. Very nice to look at, I think, especially once it ages.

 

My local lumber mill also sells "thermally modified" wood. Here's the company - Ecovantage. I have no idea if it's as advertised, but it's another option.

  • Author

I believe it's the same thing as Ipe.  A friend of mine did his entire wrap around deck in ironwood.  Went through 5 chop saw blades.  He built the seat in his steam room with it, too.  He didn't want ceramic to sit on.

Ipe is available here, I'll look into it. It's about 4 dollars a LF, if its 6 inch wide nominal. Not available in rough.

  • Author

I don't know if it's available in Ontario, but you can also look for Black Locust - it's often used as a substitute for pressure treated lumber, apparently. Easy to cut, a pain to nail. Very nice to look at, I think, especially once it ages.

 

My local lumber mill also sells "thermally modified" wood. Here's the company - Ecovantage. I have no idea if it's as advertised, but it's another option.

Upon quick searching, black locust is not available. Does it have another name?

I reskinned my deck a few years ago with a hidden fastener called "Eb-Ty".  It requires a groove or biscuit slot on both sides of the plank, but is installed entirely from above.  It looks like a plastic biscuit with a spacer on the bottom, and includes square drive stainless steel screws.   There are different versions for hardwoods and composites, but it allows plenty of movement that also might be useful on larger outdoor items.

 

Some products are now available pregrooved, but it only took me about 2-3 hours to groove 480 sq/ft of decking with a 3 wing slot cutter in a router.  I went through 3 cutter plates during the project.  I put some screws into a plywood sheet on horses, creating a jig that held two boards and allowed me to go up one side and down the other.   I'd put the router down, rotate the boards end for end, and do the second edge.

 

After 5 winters, some downright brutal, the deck still looks good.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.