Recommended Posts

Posted

Hello all,

I need help on advising which tool should i buy first for my book case project.

What I have:  Kreg pocket hole jig, makita circular saw, boch jig saw, air nail gun.

 I can not get finish cut from home depot on plywood. 

I do not know should i buy Ridgid R4512 or festool tsr55 track saw?

 

Please help.

Thanks very much

Posted

I would go for a table saw, on a Table Saw You can Dado, miter cuts, rip small boards (like a 1 x 10, into 2 or 3 boards) cross cut sled, rabbits, etc that you can't do with a track saw. 

 

My plan is to upgrade My table saw and down the road a track saw.

Posted

O and to add with your circular saw you can make track saw "like" cuts. By clamping a board to the plywood and run the saw down the board as a straight edge or buy  "clamp and cut edge guide" that you can get at any hardware store.

Posted

Ah yes, the track saw vs table saw debate.
I would suggest looking beyond this project you are working on. I believe you will be able to complete your bookcase project with either tool.

So, you may want to start considering things like shop space. Are you in a permanent shop or will you be moving a lot? Do you have to park a car in your shop? Do you plan to use a dado cutter in your table saw or do you cut dados with a router? Do you need to bring the saw to other places? Will your brother-in-law borrow your track saw all the time, but be less likely to lug off with your table saw?

Think about how you envision yourself as a woodworker and let that be your guide. I don't know if this matters to you or not, but if you end up being a woodworker for 25 years, I guarentee this will not be your last table saw. You will want to up-grade. But 25 years from now, I doubt you will need to replace that track saw.

 

These are just some things to think about.

  • Like 1
Posted

Personally i use both.  I bought the table saw first, then the track saw and then added the MFT/3 table.  Adding the MFT/3 table greatly reduced the amount of times i turned on the table saw.  If I had to move into a smaller space i would get rid of the table saw before i would get rid of the festool. 

Posted

I bought my first UniSaw 28 years ago, still use it daily ! Bought a second UniSaw 20 years ago and put a sliding table by Excalibur on it to cross cut sheet goods.

Buy quality, take care of it and it will take care of you.

  • Like 1
Posted

I would have to agree with chet and would say get the TS55. I actually built a pair of bookcases with a festool track saw and consider it much easier with a tracksaw than it would have been with a table saw. I would recommend that when you cut each side clamp them flush together and then cut both sides at once to at least get matching sides that are very close to parallel. BTW I have both a tracksaw and table saw and find that they compliment each other nicely and both would serve you well. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 49 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined