Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Fuji Mini-Mite 4 HVLP initial impressions are...

Featured Replies

...very good. As some of you may remember, I got an Earlex 5500 and just couldn't get it to spray consistently. Long story short, it had several quality problems, Earlex and Infinity Tools customer support were both great trying to make it work out, but after a month of numerous test boards, the unit had too many problems and I had to return it.

 

After a lot of research and talking with some people, the Fuji Mini-Mite 3 would probably be all I needed. I decided that $135 extra was nothing over the long haul and got the Mini-Mite 4. Loading it up with some waterborne and spraying cardboard, I quickly realized this machine blows...in a good way!

 

I did plenty of research on spraying waterbornes over the past month, and adjusted the gun based on what I learned. I sprayed 2 coats of Target EM1000 sanding sealer on 4 test boards, and while the finish seemed to flow out fine, there were some problems (fisheyes?).

 

post-8178-0-39294200-1368247647_thumb.jp

 

I sprayed some denatured alcohol through the gun when I got it but maybe that wasn't enough. It's possible some contamination came out with the finish. I took the needle out and cleaned it, then a little Vaseline about an inch from the tip on back. 

 

I sanded the boards with 400 and wiped with a 50/50 mixture of DNA/water. I loaded up some Target EM2000 satin into the gun and adjusted my fluid and pattern on some cardboard. I did 2 coats with 2 hours in between and here is what the 2nd coat looked like when applied.

 

post-8178-0-79443900-1368248021_thumb.jp

 

post-8178-0-77918300-1368248026_thumb.jp

 

Here is what they looked like an hour later

 

post-8178-0-75485600-1368248031_thumb.jp

 

I'm very happy how they turned out especially being my first time using this system. I quickly learned I need to move fast as this puts down the finish fast. 

 

First thing that comes to mind. Your spray area needs attention. You may want to get some paper down. Keep the area clean. You can get dried dusty finish kicked up back onto your surface. Water based wont melt in like a solvent lacquer.

An old card table makes a great spray platform and overspray falls off to the floor. Don't do anything over it other than spraying. Looks like spraying over your everyday work bench and that's not a good Idea.
 

 

-Ace-

I've had the same HVLP unit for 7 years.  It's a beast.  That's a Fuji gun in my profile pic!  ;)  I've got top and bottom feed setups, as well as a 2 Qt. pressure pot.  It's a terrific tool.

 

My spray table is two 2' x 2' plywood panels, with a 1 1/2" cast iron pipe flange screwed to the bottom of one, and a 2" screwed to the top of the other.    The two sizes of cast iron pipe telescope, making a turntable,  I have two sets of pipes, one floorstanding, the other for putting on a bench.  For large items, 2x4's can be screwed to the top panel to support the work.  The whole setup unscrews and stores flat.

==> My spray table is two 2' x 2' plywood panels, with a 1 1/2" cast iron pipe flange screwed to the bottom of one, and a 2" screwed to the top of the other.    The two sizes of cast iron pipe telescope, making a turntable,  I have two sets of pipes, one floorstanding, the other for putting on a bench.  For large items, 2x4's can be screwed to the top panel to support the work.  The whole setup unscrews and stores flat.

 

I've got the same rig -- I thinks it's in Dresner's spray book.  I moded the design to make the 'base' a 3'x2' open-cart on locking casters with 3" sides -- the pipe mount is centered on the cart floor... I keep tack cloth, pyramids, rags, solvents, brushes, etc. in the 'cart' so they can remain within within easy reach.

 

==> I also have the fuji system and have been happy.  I've got dedicated guns for NGR dyes (#2), shellac (#3), lacquer(#4) and water based (#4).  Saves setup/clean-up time.

  • Author

I did my first real project with the Fuji. I had sprayed Target EM1000 sanding sealer with the Earlex which I sanded all the imperfections with 320. I vacuumed the dust and wiped down with 50/50 mix of DNA/water. Then I fired up the Fuji and sprayed Target EM2000 with cross-linker added. I moved fast but it still put down a slightly milky coat. I thought it was a little thick, and after 30 minutes it still had a lot of wet spots. Here is it after spraying. 

 

post-8178-0-75464000-1368326237_thumb.jp

 

I gave it 2 hours and it leveled out and looked great. I put on 2 more coats with very light sanding with 600, vacuum, and wipe down with DNA/water. I'm very happy how it turned out even though there are a fair amount of dust nibs. A brown paper sack should take care of them in a week.

 

post-8178-0-72023700-1368326239_thumb.jp

 

I need to figure out a spray area and don't know if I'm spraying too heavy. On the test boards it was 3-4 mils and slightly milky (obviously I didn't use mil gauge on real project). I'm am getting a lot more finish in the air with the Fuji and definitely have to more faster. With the 1.4mm tip, I have it about 1.5 full turns open, spray pattern about 50% open, and the air 100% open. Don't know if I should close the tip some and/or close the air some. I like my results but wonder if I can improve my gun settings and technique more? Should I run my overhead air filtration while spraying or would that cause problems?

 

I really think I'm going to enjoy using waterbornes. The walnut test boards I use different strengths of Lockwood american walnut dye under the waterborne finish and they look like they have an oil-varnish finish on them.

One comment, after sanding a finish, wipe the finish with a cloth damp with water (more dry than wet). The 50/50 is typically for cleaning raw wood, the alcohol helps to speed the dry of the water from the wood. However, if Target recommends, then rock on! Just worry the alcohol may soften a fresh finish.

Dude....your getting it!!!!! :) :) Your final wet film thickness ("WFT")  looks perfect, I see that nice blue haze...which is around 3 to 4 mil WFT. Your doing fine, now you need a little more face time behind that windshield. Practice, keep spraying and adjusting...then one day it slaps you across the face and your golden. Now about speed...have you ever painted a house with a paint brush. You dip the brush in the can get that brush nice and wet and slap it on. Well....sorta kinda the action here. The wetter you spray (gun setting) the faster you need to move. Make sure your spraying in raking light, you need to see that finish going on wet.

Like I said before, every finish sprays a little different, some better, some worse. Get your Target coatings down, then try different manufactures, I don’t really care who's...just try.

As to the over-head air filter....... NO.....not yet! For spraying in the shop. You want the air as still as possible. When done spraying, give the finish a moment to flash off then turn on the air filter or fan to clear the shop.
 

-Ace-

 

Maaaaan is that sawdust on those saw-horses?????????????? :o:D:)

 

I need to figure out a spray area and don't know if I'm spraying too heavy. On the test boards it was 3-4 mils and slightly milky (obviously I didn't use mil gauge on real project). I'm am getting a lot more finish in the air with the Fuji and definitely have to more faster. With the 1.4mm tip, I have it about 1.5 full turns open, spray pattern about 50% open, and the air 100% open. Don't know if I should close the tip some and/or close the air some. I like my results but wonder if I can improve my gun settings and technique more? Should I run my overhead air filtration while spraying or would that cause problems?

 

I really think I'm going to enjoy using waterbornes. The walnut test boards I use different strengths of Lockwood american walnut dye under the waterborne finish and they look like they have an oil-varnish finish on them.

Test your pattern on paper. Your hand is a good size. You should not get that standing in a cloud feeling when you are done. Your tip is on the larger side for that finish .8 or 1.0 is what I prefer for that finish.

Next time you need some shop cabinets or something spray your full sheets of plywood before breaking down. Full sheets are a good way to learn to spray. Also try some solvent lacquer like Rodda crystal clear this way you can learn with a finish that levels easily and dries fast.

==> spray your full sheets of plywood before breaking down. Full sheets are a good way to learn to spray.

 

+1  that's how i learned -- back in the day, they just handed me a gun and after watching someone who actually knew what he was doing said, have at it...

  • Author

Ace - for some reason on the Target forums, they recommend a 50/50 mixture of DNA/water for wiping down the surface. On that vanity I actually vacuumed first then wiped down. The 50/50 does slightly soften the surface and will leave white streaks in areas. Spraying on the next coat and everything is fine. I guess the manufacturer is smarter about their products than I am  :D

 

I also have some General Finishes Enduro-var gloss and satin. I'm been using the Target EM2000 since I have a gallon and with the promo is was barely more than quart with shipping. So that has been my practice finish. I still want to try some other products and heard good things about Crystalac plus you can't beat $1 shipping from McFeelys. Any other premium waterbornes you guys like? I'll end up settling on a brand or two just like after experimenting with varnishes, Waterlox became my go to. 

 

Jewitt's Spray Finishing has the finishing table you guys are talking about and also a knock-down spray booth for waterbornes. I don't plan on spraying any oil-based finishes with this setup as I have no windows in my garage and need heat during "woodworking season". 

 

When I was done spraying, I wasn't in a cloud but a light haze. Would shutting the air valve some help with that? Does a 4 stage put out more air than a 3 stage or just have more power when needed? Obviously a finishing booth will help.

 

  • 4 years later...

Digging up this old thread - did you stay with the same needle, or switch to a smaller one for spraying water Bourne?

@estesbubba

  • 2 weeks later...
  • Author
On 5/26/2017 at 7:35 PM, Pug said:

Digging up this old thread - did you stay with the same needle, or switch to a smaller one for spraying water Bourne?

@estesbubba

Pug I spray all my waterbournes and shellac with a 1.0 needle. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.