RJsumthn Posted May 12, 2013 Report Posted May 12, 2013 I will be in the market for a planer in the near future. I will be looking for a lunchbox planer for their cost, size, and 110v compatibility. The one I am considering is the Dewalt H5342. What lunchbox planer do you all recommend? Quote
Nyles Posted May 12, 2013 Report Posted May 12, 2013 RJ, I have a dewalt 733 which i believe is an older model to the one you have in mind. I really like my 733, I purchased it new and its been great. The one your looking at i believe has some good options for knife upgrades so thats a plus and from what i have heard its a decent planer that most people seem happy with. Id suggest reading up on them if you have not already i believe one of the dewalt models ( i believe the 734?) has disposable knives, which I dont know if that would be an issue for you. Over all id say great choice. Nyles Quote
rodger. Posted May 12, 2013 Report Posted May 12, 2013 I have the ridgid tp1300. It is great, and the cost was quite reasonable. It also came with a stand, and an extra set of double sided blades. The only problem is, ridgid doesn't make it anymore. You can prob get one used at a very reasonable price. Quote
mikem Posted May 12, 2013 Report Posted May 12, 2013 I have the DW 734, and it is a great planer. I don't think you can go wrong on a dewalt planer. Quote
Dave's Not Here Posted May 12, 2013 Report Posted May 12, 2013 DeWalt DW735 was my choice and a good choice it was. Be sure to buy the infeed/outfeed tables for it though as they will help greatly in reducing snipe. I'm pretty sure that that H5342 model number you listed is the Grizzly number for the DW735 but I could be wrong. Quote
RJsumthn Posted May 13, 2013 Author Report Posted May 13, 2013 You're right Dave, I wrote down the wrong number. Quote
Freddie Posted May 13, 2013 Report Posted May 13, 2013 I have the 735 with infeed outfeed tables. Based on my experience, its great. While snipe is unavoidable, as long as you keep your boards extra long for milling youll be fine. Quote
pghmyn Posted May 13, 2013 Report Posted May 13, 2013 I have the 735 with infeed outfeed tables. Based on my experience, its great. While snipe is unavoidable, as long as you keep your boards extra long for milling youll be fine.Snipe can be avoidable, and the best method I use is to run a sacrificial piece before the first piece, and after the last piece. Between the sacrificial pieces, you run all your stock, end to end, never letting the pressure rollers go unsupported. Can you do it alone, yes. Not hard at all. But if you could get an extra hand for just the milling process to catch the pieces or move them out of the way, it goes by extremely fast and efficient. Or, I just thought about it, you could cut two boards 3-4 inches longer and just use those as the first and last boards every time. Then trim the snipe on those at the end. 1 Quote
Freddie Posted May 13, 2013 Report Posted May 13, 2013 Yes there is that method, but i always keep my stock extra long because you eliminate the possibility of damaging your work pieces. My logic is that even with that method you still have your work piece only catching one feed roller on the infeed and outfeed. I believe paul marcel made a video of a full sled that lays over the platen. You lose max height of the planer but you gain snipe free cuts from what i remember. Quote
pghmyn Posted May 13, 2013 Report Posted May 13, 2013 Yes there is that method, but i always keep my stock extra long because you eliminate the possibility of damaging your work pieces. My logic is that even with that method you still have your work piece only catching one feed roller on the infeed and outfeed. I believe paul marcel made a video of a full sled that lays over the platen. You lose max height of the planer but you gain snipe free cuts from what i remember.To each his own. I'm not saying you're wrong, because you're obviously not. There are tons of ways to do woodworking tasks. I you're happy with your method, keep doing it! If you're looking for a change, my method could be worth a shot. Quote
Freddie Posted May 13, 2013 Report Posted May 13, 2013 Thanks pghmyn, im always on the hunt for new ways to accomplish certain tasks. This is the only way to truly fimd the best method for oneself, to have personally tried them all, not just hear or read about them Quote
TRBaker Posted May 13, 2013 Report Posted May 13, 2013 I have the Dewalt DW735 and couldn't be happier with it's performance. I like the replaceable blades and the ease in reversing them or replacing them. Also, it is two speed, and the slower speed really allows for a smooth finish cut. Like all lunch-box planers, it has its limitations. You have to take it slow and easy on wider boards, removing just a fart-skin at a time, or it will bog down. I've used the Rigid, Delta, and Makita and like the Dewalt the best. Quote
sgmdwk Posted May 13, 2013 Report Posted May 13, 2013 I have a Delta 22-560 that I have used for a number of years. It was cheap and has double sided throwaway blades indexed on little pins - no sharpening and no jigs to install the blades. I'm sure there are much better planers out there, but this one works fine for the limited use I put it through. Quote
Tom Crawford Posted May 13, 2013 Report Posted May 13, 2013 I to will be in the market for a planer in a few months after I recover from knee replacement surgeries. Does any one have experience with the Steel City Helical head one? http://www.steelcitytoolworks.com/products_tools.cfm?section=2&category=9&tool=40200H Quote
RJsumthn Posted May 13, 2013 Author Report Posted May 13, 2013 I saw those too Tom. Very intriguing. It just seems too good to be true for that to have a helical head at that price point. I would be interested in seeing if anyone has spent time with one. Quote
dwacker Posted May 13, 2013 Report Posted May 13, 2013 I saw those too Tom. Very intriguing. It just seems too good to be true for that to have a helical head at that price point. I would be interested in seeing if anyone has spent time with one. I wouldnt get to excited about the helical. Take a look at the owners manual. I think the engineer was a comedian. Quote
dcustoms Posted May 13, 2013 Report Posted May 13, 2013 Looking at the owners manual that helical head looks funky. Only 7 teeth contact the board at any one time that are spaces approx 1 7/8 apart. weird.... Quote
Freddie Posted May 13, 2013 Report Posted May 13, 2013 Also i read horror reviews of those things loaded with packing grease that never seemed to fully come out. This was a while ago, they may have looked into that by now Quote
Alan Bienlein Posted May 13, 2013 Report Posted May 13, 2013 I saw those too Tom. Very intriguing. It just seems too good to be true for that to have a helical head at that price point. I would be interested in seeing if anyone has spent time with one. I bought that helical head and installed it in my ridgid TP1300 and never looked back! Say what you will about the engineers that designed it or how funky it looks but it works. Quote
ChetlovesMer Posted May 13, 2013 Report Posted May 13, 2013 I have the 734. Which seems to be on sale for cheap everywhere. Good value and I've had great success. Quote
mds2 Posted May 13, 2013 Report Posted May 13, 2013 I had one 734, fed about 3 feet of 2" wide maple through it and the infeed roller quit working. Took it back and got a different one, it has worked wonderfully until recently, now I'm having infeed problems again. Don't know if this is a common problem, or how to go about fixing it. Another thing about the 734, it screams like a banshee. Hearing protection is an absolute must. Quote
prov163 Posted May 13, 2013 Report Posted May 13, 2013 I have the Steel City helical head planer with the carbide blades. I love it!!! Very smooth cut, practically no snipe, fairly quiet, reasonably good dust collection. I bought it at Highland Hardware for $499 and have been extremely pleased. Quote
ChetlovesMer Posted May 14, 2013 Report Posted May 14, 2013 Good point by MDS2. The 734 is louder than ... something really loud. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.