wdwerker Posted June 25, 2013 Report Posted June 25, 2013 I have had good results with the metal Micro Jig. I have also used the +1 metal in the front holes and the orange plastic +1 in the rear holes. If I get a big pinch when ripping the orange piece pulls loose and rides in the kerf untill I can get the saw safely stopped( or finish the cut) Quote
calblacksmith Posted June 25, 2013 Report Posted June 25, 2013 P.B. Thanks, I will give them both a check out, it is hard to be too safe with 3 hp driving a sharp toothed disc, right out there in front of you! Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 Reading through this thread, and watching that video again, I decided it was time to reinstall the microjig splitter I bought years ago. I had it on this saw with the original fence, and it worked well, then I upgraded the fence, which was much more true then the old one, and the fence caused it to be too tight. So awhile back I bought a new ZCI with the purpose of reinstalling it. Then I put it off and off some more while working to complete my last project. Pushed a few test pieces through after installing it, and it now works exactly as it should. Mike, is that orange thing a splitter? Better than nothing I guess, so far away from the blade too? Crown guard would also be a great thing. Quote
mikem Posted June 25, 2013 Report Posted June 25, 2013 Yes it is. It is what Micro Jig offers as an aftermarket splitter. While it is not nearly as good as a riving knife or splitter that would have come with the saw, it is the next best thing. Also note, that there should be a second splitter in the second set of holes that help keep the off cut away from the blade. Unfortunately the holes got messed up and are not useable. Fortunately, I have found that the one seems to be sufficient for both sides of the blade. In fact that second set of holes has an option to be used for detecting when the piece starts pinching the blade but otherwise uses the one steel piece for use as the splitter. Don't let it's diminutive size fool you, and does actually work very well. As for being far away from the blade, unless I setup a ZCI for each blade height I use, that is as close as it will get. It would be nice if it was closer, but it is by far better then nothing. http://microjig.com/products/mj-splitter-steel-pro/index.shtml Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 Thanks for the follow up mike. Your saw still gives me a shiver, stay safe bro Quote
mikem Posted June 25, 2013 Report Posted June 25, 2013 If it helps, unless I am pushing a wide sheet of plywood through, I pretty much always use a push stick. The reality is, the saw is around 30 years old, I am hoping I can get another year or two of usage out of it. I would love to go out and buy a sawstop tomorrow, but reality is, I don't have the $2500 right now to get one. Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 That's cool mike. Sawstop seems a real big thing in the US, this forum introduced me to the concept. It's a very interesting solution. Quote
dwacker Posted June 25, 2013 Report Posted June 25, 2013 That's cool mike. Sawstop seems a real big thing in the US, this forum introduced me to the concept. It's a very interesting solution. I would buy a power feed before thinking about a saw stop. With so many people afraid to cut sheet goods and using track saws I would think power feeders would be more common that they are. I can rip 2.25" stock all day and not worry about getting close to the blade. Quote
calblacksmith Posted June 25, 2013 Report Posted June 25, 2013 P.B. Thank you for reminding me about those options. I remember that when I first bought the saw, I looked at them but it has gone to the back of my list. I just ordered the complete setup, the works. The down side is that there is a 12+ waiting list. Until then, the mico jig pro will have to do on the zero clearance throat plate. I had intended to only use the zero clearance but I am not sure that the shark works on them. I guess I can cut a slot for it though. Thanks again! Sorry to the OP, I did not intend to hijack the thread. Quote
dwacker Posted June 25, 2013 Report Posted June 25, 2013 P.B. Thank you for reminding me about those options. I remember that when I first bought the saw, I looked at them but it has gone to the back of my list. I just ordered the complete setup, the works. The down side is that there is a 12+ waiting list. Until then, the mico jig pro will have to do on the zero clearance throat plate. I had intended to only use the zero clearance but I am not sure that the shark works on them. I guess I can cut a slot for it though. Thanks again! Sorry to the OP, I did not intend to hijack the thread. Your welcome, hope all works out. Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 I would buy a power feed before thinking about a saw stop. With so many people afraid to cut sheet goods and using track saws I would think power feeders would be more common that they are. I can rip 2.25" stock all day and not worry about getting close to the blade. PB I would recommend a power feed all day on a shaper, so much so we never hand feed anything unless it's ring fence work. Our rip bench came with power feed and unless we are running a huge meter run it's too fussy. Even more so on the panel saw. Our work is not huge volume so we would be adjusting it too much. With a close fitting riving knife and a crown guard safety is already at a high level. To my knowledge and from a European perspective the only saws you see a power feed on is a band re-saw. Even the Daddy panel saw does not come with a power feed. Quote
dwacker Posted June 25, 2013 Report Posted June 25, 2013 PB I would recommend a power feed all day on a shaper, so much so we never hand feed anything unless it's ring fence work. Our rip bench came with power feed and unless we are running a huge meter run it's too fussy. Even more so on the panel saw. Our work is not huge volume so we would be adjusting it too much. With a close fitting riving knife and a crown guard safety is already at a high level. To my knowledge and from a European perspective the only saws you see a power feed on is a band re-saw. Even the Daddy panel saw does not come with a power feed. I have no issues running the power feeder on a tablesaw been doing it for decades. For repetitive narrow ripping you cant beat it for safety and over all comfort. Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 As long as it was very repetitive I would look into it. Quote
Spencer_J Posted June 26, 2013 Report Posted June 26, 2013 The micro jig steel pro has completely changed my views on this topic. I have an older unisaw and boy would i have to chop up my zero clearance insert to get a knife in there. Also, the mj splitter was about $30. It came with great directions and everything needed to make it happen except the1/2" mdf. I too screwed up the rear holes and i only use the front guy. It helps me determine when things aren't aligned properly like when i just changed the blade. I can feel the resistance between the workpiece and my fence. Its also a very low profile little thing so i can make deep non through cuts on large chunks of wood. As long as my face touching the fence is square, i know that the whole chunk will have a perfectly sawn face. It will also keep crap from drifting into the back of the blade such as posted in this video. I have not had one kickback since i installed the thing. Also works great with my sliding table if i have a heavy offcut, it helps keep things split. I consider it an upgrade to the biesemeyer knife. The mj splitter steel pro is an all around star in my studio. Quote
nod Posted July 10, 2013 Report Posted July 10, 2013 wow. I know I'm late to the party, but I'm new here. This video is nuts. I've been considering some older table saws to replace my current POS, but I will NOT be buying anything without a riving knife. or at least anything that can't have one added. yikes Quote
G S Haydon Posted July 10, 2013 Author Report Posted July 10, 2013 nod, it's a hair raiser! Add a crown guard too. Without it it can still come and get you Quote
nod Posted July 11, 2013 Report Posted July 11, 2013 i hear that. Always a safety freak. Actually just found a sawstop cabinet ts for sale barely used. would loove to do that, but out of my price range. c'est la vie. i'm sure more will be coming up for sale in the next year/two down the road Quote
G S Haydon Posted July 11, 2013 Author Report Posted July 11, 2013 A saw stop would be nice. I think some of the reason why saw stop does not have much traction outside North America is because European stuff as a rule has a riving knife and a crown guard. I think you are far from a safety freak, just good practice in my eyes. Quote
rodger. Posted July 11, 2013 Report Posted July 11, 2013 A saw stop would be nice. I think some of the reason why saw stop does not have much traction outside North America is because European stuff as a rule has a riving knife and a crown guard. I think you are far from a safety freak, just good practice in my eyes. One time a guy i knew, who ran an office furniture installation company, was selling up and asked me if I was interested in a table saw. I said I would def take a look at it. When I arrived, I noticed it was at one time a nice cabinet saw. Unfortunately, it had no blade guard, no splitter, and the fence was bent. It was scary just to look at, but he said the guys there used it. I wouldn't even be in the room if someone was using it. Quote
ChetlovesMer Posted July 12, 2013 Report Posted July 12, 2013 Wow, this is actually the first time I ever saw this video. That dude is nuts, but the video is very informative. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.