snichols Posted July 17, 2013 Report Posted July 17, 2013 I'm in the process of evaluating moving fillister plane from Josh Clarke (Josh rules!). You can see from the attached picture that I installed the blade incorrectly (Josh straightened me out) but even when I had it installed correctly I wasn't sure how to make the plane perform well. I'm looking for good resources for how to do the following tasks with this plane: 1. How do I get the iron OUT once I have it installed and the wedge set? 2. How do I advance or retract it once the wedge is set? 3. How do I sharpen it the blade? It looks like the "side" of the blade was previously sharpened? Is that right? I've seen a lot of online videos and articles but I'm not sure if any are dedicated to this specific style of plane. Any help is appreciated. Thanks, Shawn Quote
skiback46 Posted July 17, 2013 Report Posted July 17, 2013 for both 1 & 2 I hit the back of the plane against my bench. Start somewhat lightly, and gradually hit harder till you achieve the desired affect. When I set my blade I usually set it a little shy than easy it forward with light taps on the iron and then the last one on the wedge to lock it in place for 3; I freehand my moving fillister blade, and I don't sharpen the side, as I don't want it to cut the wood on the side. The blade should be set so that the farthest protrusion of the side (should be at the corner of the side and cutting edge) is in the same plane as the body, I would make sure that its a nice surface, so it doesn't mar or catch on the wall of the rabbet. The other thing to be aware of is the nicker. If its sticking down too far, you will have trouble getting full contact across the blade. Quote
Tom King Posted July 17, 2013 Report Posted July 17, 2013 The wedge is on the wrong side of the iron. To lossen the blade, hold the plane body in your hand, and tap on the back of the plane body. Don't use a steel hammer. For wooden planes, I use an Estwing hammer that has two different density faces. One is yellow, and the other red. I use the softer face for loosening, and the harder face to tighten the wedge. You don't have to tap the wedge very hard at all to tighten the wedge. For molding planes, I usually set the body down on wood, let the iron rest where it will in place, and a light tap on the wedge will give you a cut of a few thousandths. A tap on the front of the body will advance the iron, if the wedge is not jambed in too tight. Adjustment is all about tapping with the plane hammer. Again, never hit one with a steel hammer, and even with a proper hammer, never hit anything hard at all. Once you get it adjusted right, and are finished using it, one light tap on the back of the body should release all the tension in the wedge. Then I wrap in a cloth, and store it back in its toolbox. I use molding planes all the time. The back of the iron near the cutting edge needs to be polished just like a chisel or any other plane iron. Super Duper Damn sharp will solve all sorts of problems with a molding plane. It looks like a nice one, and especially since the nicker is still there. The boxwood (I'm guessing ) sole and throat look like they are in pristine shape. It should work really good. I use the nicker more going backwards than forward. Pull the plane backwards and the iron won't cut, but the nicker will nick the line of the shoulder, helping indicate where the rabbet will be. You can see the hammer I use for molding planes in this picture: http://www.historic-house-restoration.com/images/april182013_003.JPG I've seen more expensive ones, but I doubt they work any better, just prettier. Quote
richard arnold Posted July 17, 2013 Report Posted July 17, 2013 Hi there. The first thing you may want to do is put the wedge in front of the iron as it's the wrong way round at the moment. I tend to adjust irons in wooden bodied planes by striking the heel with a hide hammer, or a wooden mallet. You can advance the cut with gentle taps of a hammer on the iron. Cheers Richard Quote
G S Haydon Posted July 17, 2013 Report Posted July 17, 2013 Hi Shawn, First of richard arnold (last poster) is a very knowledgeable on these kind of tools and has a section on fillisters on his website. A caveat on my advice, I am a rank amateur on wooden planes. Just to echo others, and as you mention, the wedge is in the wrong place. 1. Over or resting on a bench hold the plane with one hand with your thumb pushing up on the wedge, strike the back of the plane firmly with a wooden mallet/ hide hammer. The shock of the blow combined with the thumb pressure should pop the wedge. 2. To advance the cutter strike the front of the plane or tap the blade. To retract the blade strike the back of the plane. Secure the wedge after adjustments 3. The reason the blade looks sharped is because its tapering away so that the side of the blade does not come into contact with the rebate upstand. No need to sharpen this edge. I will expect Richard to come along and put me right if any of that advice is not good. Quote
baok Posted July 18, 2013 Report Posted July 18, 2013 I visited the shop of Larry Williams at Old Street Tool and he coached me on this. He retracts the iron exactly as described in earlier responses. He advances it with light taps directly on the back of the iron with a brass hammer and then follows with a tap on the wedge with a non-marring hammer (to keep it tight). I don't think it would have to be a brass hammer specifically; just a hard hammer as opposed to a wooden, plastic, or rubber mallet. Quote
snichols Posted July 18, 2013 Author Report Posted July 18, 2013 Thanks for the input guys. I'll try this out and report back. Quote
RenaissanceWW Posted July 18, 2013 Report Posted July 18, 2013 Its possible that someone was just cleaning off some rust and that is why the side of the blade looks sharpened. I have found skewed blades to be the best blades to learn freehand sharpening with because they present such a wide bevel face to register on the stone. One point about setting the blade. You do want the leading point to stick beyond the body of the plane by a hair or less. Don't set it flush. This is one of the eccentricities of rabbeting planes and will cause you to create a sloping shoulder. The point of the blade must get all the way down into the inside corner of the rabbet or each successive pass will push the plane out a bit resulting in a minutely stepped shoulder. I don't recommend measuring this as it is probably less than 128th of an inch protrusion but if you run your finger along the side of the plane, it should catch on the point. I have heard this protrusion is needed as a result of flex in the wood as the leading edge of the plane compresses slightly. Whatever the reason, it is necessary to get a square shouldered rabbet. Quote
derekcohen Posted July 21, 2013 Report Posted July 21, 2013 Hi Shawn The easiest way to remove a tapered blade (such as yours) is to drive the blade through the plane. Do not try and wack the rear of the plane's body - this method only works when the wedge is not jammed in. Simply tap on the end of the blade's shaft that sticks up beyond the wedge. This will loosen the wedge as well. (That is why one should always tap the wedge down securely when ever you increase the blades projection). Yes, the wedge should sit on the outside of the blade. And, yes, the blade needs sharpening before it is used. (Who believes the fairy tale that blades come ready for use?). Note: the above does not apply for wooden planes with parallel blades. Only for tapered blades. Regards from Perth Derek 1 Quote
richard arnold Posted July 21, 2013 Report Posted July 21, 2013 Just thought I would mention one other method of removing sticky wedges. This one requires a bit of patience though. It may be that depending on where the plane has been stored that it has picked up a certain amount of moisture. If this is the case it may be worth while placing the plane somewhere nice and dry for a week or so. A few years ago I discovered this very rare plane by John Davenport. Try as I might I could not shift the wedge. It is an extremely delicate wedge and I was fearful of damaging it, so I placed the plane on top of our central heating boiler for a week and hey presto the wedge came out with ease. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.