Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Getting the Internet into my shop

Featured Replies

Well if someone with a Network degree, 10 years of IT experience (including broadband installation), cant throw in his 2 cents.   

 

You can try all the above and most of it may work.  In my experience you should NEVER use EoP (Ethernet over Power), they have a tendency to fry things or frequently drop packets.  You can use wireless but it will be subject to EMI.  If you go this route, you will want directional antennae on the outside of the house and outside of the workshop.  Best practice, you have two bridges that run into switches on both ends. Sure you can hook antennae directly into the computer and wireless router, but its not best practice.  

 

If you are to bury cable, please use underground rated wire.  The cat 5 or cat 6 you get at your local box store will degrade underground and is not shielded.  The underground rated cable is filled with a water displacing gel and has a thicker sheathing, plus some have grounding layers.  Best practice here is to bring it up to a NID (Network interface Device) with lightening arrestors on each end and each wire.  It lightening strikes the ground and your buried cable isn't protected, it could fry everything hooked up to it.  Off of the NID you can bring a cat 5 or cat 6 inside to a switch (or wireless AP so you can have wifi in the shop), then hook whatever network devices you have to the switch.

 

You can get a separate internet service installed in the workshop.  You may get charged full monthly rate for it.  Also you may be responsible for installation charges.  If you have Coax (cable tv) running from the house to the workshop, you can use converter boxes.  Ethernet to Coax is flaky at best and highly subject to stray voltage on the coax shielding.  

 

http://www.zhone.com/products/ZNID-GPON-4100/  example of an ethernet NID

If you go the trenching way, don't simply bury any kind of cable.  Since the distance is not that far, get a roll of black polyethylene pipe, or buy cheap plastic conduit and bury that in the trench.  Use a shop vac to pull a mason's line through it with a little rag tied on the end towards the vac.  Use that to pull the wire with.  When you pull the wire, pull another mason's line along with it, so you can pull something else in the future that hasn't  been invented yet.  This allows you to change the wire or pull something else any time in the future without trauma to the yard or wallet.

 

I built spec houses for 35 years and always did this with a couple of length of poly pipe, so no one ever had to run a trench through the yard.

 

You can also pull a 3-way switch wire through it so you can turn the lights on in the shop from the house.

 

Get something like 1-1/4 or 1-1/2.   If you use plastic conduit, remember which way the joints go.  You can only pull something through it one way easily.

  Use a shop vac to pull a mason's line through it with a little rag tied on the end towards the vac.  Use that to pull the wire with.

What a great idea!

i usually use a plastic grocery bag or my the sandwich bag from my sandwich (after i eat it of course).  The string through the conduit technique works wonderfully.

 

I agree with Tom and Aerofly.  Aerofly hit it spot on with his assessment in my opinion.

 

i would like to point out if you do the conduit/pipe thing for the future PLEASE make 2 runs of pipe. 1 for the low voltage (phone, internet, cable,speakers etc) the other for your line voltage (or 3 way switch)  Its generally frowned up to stick low voltage and high voltage stuff in the same enclosure or conduit.  Possible safety issue as well as performance issue.  Safety wise they dont want line power accidently going on a wire not rated for that kind of voltage or ampacity (which cat 5 is not) and performance wise you dont want to end up with interference or poor performance from issues created from the line voltage wires.

 

 

Nyles

I've heard running network wires parallel to the power wires greatly increases EMI problems, but running them perpendicular to power reduces the problems to the lowest possibilities.  Could you explain how 2 runs of pipe is effective?  (While I don't have as far to go, I am considering expanding a couple of locations with power and/or internet access.  One of which is my own shop, although there's going to be some other issues I need to resolve first.)

We always used three runs of pipe. Local code will not allow high voltage, low voltage or water to occupy the same conduit. You could use one run of pipe sized to pull conduit through, but most guys dedicate the pipes as the conduit for electrical and only pull water if it is pex and they need multiple zones or hot/cold. This was always with yard hydrants or irrigation in mind because sewer always requires more engineering. Electrical, data or water can be added almost at will if the pipe is already there.

Do a search on "High Gain Antenna" they run in price from 10 to several hundred dollars. My barn is a little farther from my house and I get pretty good reception. The one I have looks like a tiny satellite dish and it's highly directional so I can point it in the general direction of my router in the house and O ordered it from Best Buy online.

 

All of the houses in the neighborhood are on about 10 acres and I can now see almost everyone's networks around me!

if you run the wiring in a parallel installation you in effect are following the route of the wiring you are trying to minimize exposure to.   IE low voltage to high voltage.   So it would look like this in a parallel wiring = one - being the low voltage and one - the line voltage.  If you ran them perpendicular it would look like this + again one - being the line voltage wiring and one - being the low voltage.  You can see you have much less exposure, surface area, what ever you want to call it.  There by limiting the amount of noise the line voltage could create on the low voltage.  As a general rule of thumb if your a few feet away in your wiring you should be fine even with out conduit.  If your running conduit having the conduit side by side should not cause issues, if your worried about it separate the conduit a little in the trench.  To be honest most of the low voltage wiring these days has such good shielding you pry wont see any issues even if you just ran the two side by side.  Most of the problems I have seen are on older pre existing wiring in a home.   On the off chance your using sensitive equipment or just want the best performance or to be as safe as possible as far as avoiding problems then follow the advice youve been reading here about separating the two.  I would not suggest sticking it in the same conduit.  The conduit just adds a physical layer of shielding, nothing more.  Couple that with good wiring practices and you shouldnt have any issues.  

 

For what ever its worth and to whom ever cares conduit is your friend.  When you buy a home before you landscape the yard stick a run of conduit in.  You dont even need to hook it upto anything just run it out in the yard mark it some how and terminate the run up against the house near the panel.  Youll save yourself headache, time and money.  Same goes before you build that out building, barn, or garage.  If you need 1 run of conduit run 2 or upsize the one run several sizes.  Conduit is cheap, real cheap compared to digging up sod, breaking out concreate, trenching, replacing existing conduit that was to small etc.  Its a long term cheap investment that could save hundreds if not thousands down the road.  So the next home you build, buy, or have a home  built tell the contractor you want that done, Itll be pennies on the dollar and I think most people who have done it and had to use it will tell you it was a well worth while investment.

 

 

Nyles

Nyles, I was incomplete. You have the sage advice. Every sidewalk, every driveway, every large planting bed near a tree. You never want to dig those areas up and the conduit/ pipe is cheap. When I referenced three pipes, those were dry pipes under walkways and drives. Homeowners were always deciding to add water, data, or power to their lake rooms, boathouses, or outbuildings late in the project. It may be too late OP but if you have to move under your drive, put more pipe than you ever think you'll need.

+1 on what CS said. I used to put three 3" PVC pipes under all walks and drives for just this purpose. You had all the room you needed to run multiple conduits or water pipes under the concrete or asphalt without trenching and patching.

I'd go the wireless extender route, the detachable antenna's are good, u could even find extended range antenna's to replace the ones the device came with to up the juice intake. Just make sure your router at home is in direct line of sight of the antenna's and you should be just fine.

Could always try the old beer can wifi antenna booster ;-)

 

http://www.youtube.com/watch?v=aUYGb2JtQYA

 

That would be an example of a parabolic directional antenna.  Also to clarify... a high gain antenna = directional antenna.  It focus the radio waves into a narrow band to improve signal.  Versus an omni which is a wide broadcast, like a TV or Radio station.

 

The question the OP needs to answer.... if he spends a few hundred on good antennas,,, would he get a better ROI to trench, run conduit, get a wired connection, and leave room for expansion for a few hundred more.

Ethernet has differential pairs which is pretty immunte from noise. But, 70 yards was it, that is getting long.

 

As far as running condiut, that is a lot of money (or time) and expense to push ethernet.

 

I would be temped to try 2 access points with resonably directional antennas on the sides of the buildings. But that is just me. My back garage is wood construction and I have an Apple AirPort express in there that works just fine about 100' from the LinkSys dual band 802.11n router (on the other side of the house in a second floor closet). My iPhone and iPad also work well from the house LinkSys router.

Quality and location of the wireless access device in the house is something to pay attention to!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.