mds2 Posted October 29, 2013 Report Share Posted October 29, 2013 If you have the 2013 issue of Tools and Shops from FWW you have probably seen the article on L fences. I had never seen one before but the article showed a lot of practical uses. I built one tonight. Really couldn't be simpler and took all of two minutes. Does anyone here use one? http://i.imgur.com/yx6HcJP.jpg 1 Quote Link to comment Share on other sites More sharing options...
Pbmaster11 Posted October 29, 2013 Report Share Posted October 29, 2013 what are they used for? Quote Link to comment Share on other sites More sharing options...
mds2 Posted October 29, 2013 Author Report Share Posted October 29, 2013 It showed uses like, rabbeting, tenoning, jointing, cutting out patterns with straight sides (I found that part very interesting). It also showed some ways to cut miters. I haven't used it yet. I plan on trying some things out tomorrow. Quote Link to comment Share on other sites More sharing options...
mds2 Posted October 29, 2013 Author Report Share Posted October 29, 2013 Another angle. The blade sits in line with the left side of the jig. The off cut falls beneath it. http://i.imgur.com/ZpmrSGp.jpg Quote Link to comment Share on other sites More sharing options...
CessnaPilotBarry Posted October 29, 2013 Report Share Posted October 29, 2013 I keep one hanging above the saw. In fact, I learned to use one on the exact same pair of saws shown in the article... Bob covered the uses pretty well. Most of the times you'd use one are to prevent waste stock from being trapped between the blade and fence, like lopping off tenon cheeks, or cutting large rabbets in two passes with a single blade. It saves a bunch of time to cut the tenon cheeks vertically, then use the L fence Adding a flat area to a curved or oddly shaped part is another fantastic use. Simply attach a carrier rail or a pair of nails to ride the fence. Quote Link to comment Share on other sites More sharing options...
mds2 Posted October 29, 2013 Author Report Share Posted October 29, 2013 I dont have a jointer and it looks like this will solve at least one problem for me. Barry, do you use yours much? Quote Link to comment Share on other sites More sharing options...
CessnaPilotBarry Posted October 29, 2013 Report Share Posted October 29, 2013 I dont have a jointer and it looks like this will solve at least one problem for me. Barry, do you use yours much? In spurts... I keep it handy above the saw. I might not use it for months, then it's the ticket! It only takes a few minutes to make. Quote Link to comment Share on other sites More sharing options...
pghmyn Posted October 29, 2013 Report Share Posted October 29, 2013 I might be the only one, but I still can't picture the use of it. Any videos? Quote Link to comment Share on other sites More sharing options...
Tpt life Posted October 29, 2013 Report Share Posted October 29, 2013 2 Quote Link to comment Share on other sites More sharing options...
Pbmaster11 Posted October 30, 2013 Report Share Posted October 30, 2013 interesting! Quote Link to comment Share on other sites More sharing options...
CessnaPilotBarry Posted October 30, 2013 Report Share Posted October 30, 2013 Not surprised Tommy did a video on it. The guy who taught it to me was a North Bennet St. instructor for 15 years. There are many other uses, as Bob described in the FWW article. Quote Link to comment Share on other sites More sharing options...
Bombarde16 Posted October 31, 2013 Report Share Posted October 31, 2013 So, it turns the table saw into a flush cutting router that can only move in straight lines. What else can it do? Quote Link to comment Share on other sites More sharing options...
CessnaPilotBarry Posted October 31, 2013 Report Share Posted October 31, 2013 So, it turns the table saw into a flush cutting router that can only move in straight lines. What else can it do? There's a great article in the current FWW Tools and Shops, but in short, it works: - As a standoff, anytime an offcut could be trapped between the fence and blade. For example, cutting tenon cheek or wide rabbet waste free, after making the vertical cut. - As a surface to run a carrier board, or even two nails, against, creating a straight edge on a board without the parallel edge required by a normal fence. This is great for joinery on curved parts. - Repeatable flush cuts on panels without parallel sides. The advantage over flush cutting straight lines with a saw over a router is speed and quality. The router requires either rough cutting to approximate size, or many passes, as well as minding the grain. The saw does it in one pass, regardless of the amount of waste coming off, and won't destroy parts or kick back by catching rising grain. A really sweet way to make some of these odd, but straight sided, parts is to set the L fence to cut 1/32" proud of the pattern. Take the part to the router table, with the pattern still attached, and climb cut the final thirty-second at the router table. As with most techniques, this is not the only way to do something, but is a great arrow in the quiver that requires very little to acquire. 1 Quote Link to comment Share on other sites More sharing options...
PeteJr Posted November 2, 2013 Report Share Posted November 2, 2013 I was stunned I never heard of an L fence in 30 years of woodworking. I'm building one and thank you FWW and the folks on this post for the excellent info. Quote Link to comment Share on other sites More sharing options...
Rick A McQuay Posted November 3, 2013 Report Share Posted November 3, 2013 Ah, I can do that with my Unifence to some degree but the height is fixed. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.