Recommended Posts

Posted

Hi All, not sure if this is the correct area, but it would be cool to see a list of people's really go-to tools when it comes to hand and layout tools. Yes, I know some things are very dependent on the type of stuff you build and how you build it. However, it seems there's probably a lot of tools that get used a majority of the time no matter what you're doing. As a beginner woodworker, having a list would be very help in determining priority of purchase. If you could add a general description of what you make, that would also help.

 

My problem right now is that I go to Lee Valley or Highland, etc... and there's so many different little hand or layout tools that look really cool and helpful. When I start to add them to my wish list, it doesn't take long before all these little tools add up to or more than a nice power tool. An example of a recent purchase of stuff that I think I'll need ended up being quite pricey. When added all together, it was hundreds of $$'s. I just want to make sure that here in the beginning before I really have any projects under my belt, that I'm not purchasing stuff that ends up being unused most of the time. Lastly, I guess I'll say something that is probably obvious: I want my projects to end up being high quality and looking good and I hate when I have to do a workaround with tools that aren't right for the job.

 

Here's my list so far, so let me know what you think:

 

purchased:

-incra pro 12" rule set

-woodpecker 12" aluminum square

-woodpecker 24" t-square

-digital calipers

-a-line table saw setup gauge

-veritas honing guide

-marking gauge

-compass

-drill bit stop collars

-knew concepts fret saw (for cutting dovetails)

-extra fine tooth Dozuki saw

 

Wish list (this is the short list:):

-set of cabinet makers rasps

-spoke shaves

-starter planes (probably at least a block and no. 4 or 5 hand plane)

-some sort of scribing tool

-set of drawing curves/templates

Posted

I have plenty of other specialty items, but these are what I'd want on the proverbial desert island.

 

My "go to" layout and marking tools are pretty straight forward...

 

Pencils, chalk, and crayons, of all shapes, colors, and sizes

Starrett 6" combo square for the apron pocket

Starret 12" combo square, with additional 18" and 24" blades

A 6" steel ruler and Woodpecker's stop

TiteMark marking gauge

FastCap 16' tape

Veritas striking knife

8' folding rule

Large and small Veritas bevel gauges and Bevel Boss

A few pairs of flea market dividers

One of those $6 brass 4" sliding calipers

Veritas saddle square

Harbor Freight 3', 4', and 6' straight edges

Plastic drafting triangles of various sizes and angles

 

 

 

For the hand tools, be aware that I use machines... the all-star team in no particular order:

Sharpening gear

Bench with workholding ability

Rabbet block

Smooth plane

Jointer plane, preferably bevel up for flexibility

Card scraper, file, & burnisher

Shoulder plane

Router plane & blades

Bench chisels (1/8, 1/4 1/2, and 3/4)

Fishtail chisel

Back saw

Fret saw

 

Again, I've got plenty of other stuff, but this is what's out all the time.   Anyone who needs shaves, rasps, carving or inlay tools, etc...  knows they need them.

 

I rarely use my jack plane, as everything it would do is covered by a machine.  

Posted

Unlike Barry, I'd take a flare gun to a desert island.

 

But like Barry, I'd include the two sizes of Veritas bevel gauges. Love the locking mechanism for one-handed use. Veritas saddle square is really nice as well.

 

From J's wish list, the rasps are a lot of fun; I don't think there are good cheap rasps; it's a "get what you pay for" kinda thing.  Spokeshaves are also a lot of fun for shaping.

 

For scribing, you have pencils. If you mean marking (as opposed to scribing an existing contour) then nice marking knives and scratch awls are a good choice. I use a Blue Spruce marking knife; besides being pretty, the flexible blade and extra-long blade options are fantastic for transferring dovetails.  The Blue Spruce mallet is really nice, too.

 

Good choice on the Knew Concepts fret saw; love mine. Which reminds me, I lent one to a friend in the UK... need to make a phone call :)

Posted

I’ve always been reticent to spend too much on tools – thinking that there is probably a way to accomplish the same goal more cheaply. To that end, I have ended up with the following things I reach for most often. First measuring and marking:

1) A 4” steel engineer’s square I bought at a local tool store for $5.

2) A mechanical pencil with .5 mm lead.

3) A Veritas wheel-type marking guage.

4) A Veritas marking knife.

5) A Stanley 25’ tape measure.

6) A Craftsman combination square.

Tools: (here’s where I occasionally spend real money)

1) A vintage (restored) Stanley #4

2) Restored Stanley #7C

3) Veritas dovetail saw

4) A set of 4 Marples Blue Chip chisels. I think they’re now sold as the Irwin brand.

5) Homemade bench hook

6) Homemade shooting board

7) Record low-angle block plane

I’ve only ever purchased these things as I needed them. Anyway, these are the things I reach for most often. I have other tools of course that I use occasionally.

Posted

My go-to layout tool is a No.4 Berol Mirado (no longer made, but you can occasionally find them on ebay) pencil, sharpened on a crank handle pencil sharpener.  I laid out 126 mortises today, and had to sharpen once.  12" combination square would be second most used.

Posted

 

Good choice on the Knew Concepts fret saw; love mine. Which reminds me, I lent one to a friend in the UK... need to make a phone call :)

That's on my list because of your videos...haha

  • Like 1
Posted

My go-to layout tool is a No.4 Berol Mirado (no longer made, but you can occasionally find them on ebay) pencil, sharpened on a crank handle pencil sharpener.

 

 

I think good pencils may be one of the most misunderstood and under appreciated tools...   That's why we have to find them on eBay!  

 

I keep good pencils, 2mm lead holders, pointer, scrap of 320 grit glued to a flat scrap, and an assortment of leads handy.    The lead can be fat and soft for writing part id's, or marking rough lumber, pointed and hard compound for general marks, or easily chisel shaped on the sand paper for extreme precision.   A neat trick with the lead holder is to slide the point out two inches, or so, and it'll fit where not much else will, like in between skinny dovetail pins...

 

When doing precision marking, zip a flat on one side of the lead point, like a chisel point, onto the lead using the sandpaper block, and put the flat against the part or tool guiding the tip.  You can even use soft pencils, to make the line easy to see. 

 

Your cutting goal is the point where the clean wood and pencil line meet, so it doesn't matter how fat the line is...   This is the same idea used in American Football, where the front edge, the transition from the green of the field to the white of the wide goal line, as the determinant for a touchdown.   Hockey is the opposite, the entire puck must cross entirely into the white, on the back of the red goal line.  In all cases, the line can be fat, the edge is very definite and clear.

 

I love  :wub:  knife marks when I need an indentation to guide another tool.  But knife marks can be really hard to see during general work, so they often require a second step of retracing with pencil or chalk.  They're also hard to correct if you put them in the wrong spot...  :huh:

Posted

This thread is evil.

 

I have already stated composing a new Lee Valley order for a few things mentioned above.

 

I will echo my love for their striking knife. It definitely is a huge upgrade from an Xacto or a utility knife.

  • Like 1
Posted

This thread is evil.

 

I have already stated composing a new Lee Valley order for a few things mentioned above.

 

I will echo my love for their striking knife. It definitely is a huge upgrade from an Xacto or a utility knife.

 

More evil... Lee Valley has free shipping through November 14 :) They already got me good last night...

Posted

I think good pencils may be one of the most misunderstood and under appreciated tools...   That's why we have to find them on eBay!  

 

I keep good pencils, 2mm lead holders, pointer, scrap of 320 grit glued to a flat scrap, and an assortment of leads handy.    The lead can be fat and soft for writing part id's, or marking rough lumber, pointed and hard compound for general marks, or easily chisel shaped on the sand paper for extreme precision.   A neat trick with the lead holder is to slide the point out two inches, or so, and it'll fit where not much else will, like in between skinny dovetail pins...

 

When doing precision marking, zip a flat on one side of the lead point, like a chisel point, onto the lead using the sandpaper block, and put the flat against the part or tool guiding the tip.  You can even use soft pencils, to make the line easy to see. 

 

Your cutting goal is the point where the clean wood and pencil line meet, so it doesn't matter how fat the line is...   This is the same idea used in American Football, where the front edge, the transition from the green of the field to the white of the wide goal line, as the determinant for a touchdown.   Hockey is the opposite, the entire puck must cross entirely into the white, on the back of the red goal line.  In all cases, the line can be fat, the edge is very definite and clear.

 

I love  :wub:  knife marks when I need an indentation to guide another tool.  But knife marks can be really hard to see during general work, so they often require a second step of retracing with pencil or chalk.  They're also hard to correct if you put them in the wrong spot...  :huh:

A no.4 Berol Mirado will hold a sharp enough point that all that is not necessary.  I haven't found any other pencils that work as well.  I believe they stopped making them in the '80s, but I have a good lifetime supply.   I can even lay out really small dovetails with one without having to resharpen.

 

Now I have a 28" waterproof toolbox labeled "Mark" that has about 30 lb. of marking stuff in it, but these pencils get called on hundreds of times before that toolbox gets pulled out of its cubby.

Posted

My must have layout tools are a marking knife, .5mm pencil, at least 2 marking gauges (I prefer Veritas wheel gauges) bevel gauge (I love the old Stanley #18's). A 6", 12", 36" 48", 72" rules. A couple dividers (the old Starretts are nice and decently priced). 12" and double 4" squares (6" combo is nice but not a must) what is a must is quality. I only trust Starrett and PEC for these.

For hand planes you can get a long ways with a router plane, block plane, a #4, and a #7, I have many old planes and several new top of the line, with some elbow grease the old ones can do every bit as good, with that said getting a new quality plane first will show you how they should work (I wish I would have taken this road as is saves you so much time and frustration). A spokeshave is your best friend for curves and I love Veritas. If your breaking down all your stock by hand a good rip and crosscut saw (I use power for this). A dovetail saw and small crosscut saw goes a long way for joinery and it's all I have ever needed. A couple mortising chisels and a few bench chisels round out the list.

To use the tools they must be sharp, I use oilstones but there are many options. I freehand sharpen now but I didn't for years and I'm glad I didn't. There is enough to figure out without throwing that into the mix too, I like the MK11 the best but a cheap one will get you going. Hope this helps some

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 35 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined