Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Safety Tip (read: warning) of the week

Featured Replies

When using a nailgun, even if they're only 18g nails, remember to check the length of the nail against the thickness of the material you're nailing together. That 16th of an inch over is still a 16th of an inch that can (and did yesterday) end up in your finger.

 

*sigh*

 

I had been nailing pieces of plywood other for some shop furniture so the 1 1/4" nails were fine, but when I switched to the thinner pieces of pine and plywood I forgot to switch to shorter nails. Lesson learned. No major harm done.

Ouch. Glad it wasn't serious.

Good advice.

Been there, done that, got the T-shirt ;).  Speedy recovery!

  • Author

I used to be an x-ray tech. I still remember the guy who came in through the Emergency room with 4 inch or so nail stuck out of his hand. He'd been using a framing nailgun or something like that (the morphine made it a little difficult to get a full story out of him). He'd fired the nailgun, the nail had hit a knot and the misfire shot the nail through his hand, parallel to the palm. It was some of the weirdest x-rays I've taken. Missed all the bones. Lucky sod ended up with muscle and tendon damage (and I assume some nerve damage), but that's comparatively easy to repair.

 

(Not the most gruesome - that would probably be guy who lost his index finger and thumb to a bandsaw on a job site)

Years ago, I bought a nail gun that shot 16p nails.  THE VERY FIRST NAIL THAT I SHOT was through two boards that I was holding together with my left hand.  The nail came out of the other side and brushed against my index finger as it exited the boards. no injury but my hinny ....hiney....hiny.....HOW DO YOU SPELL BUTTOCKS????.....Anyway, it tightened and I've been over the top, crazy careful ever since with all of my nail guns.  Glad it was not a bad injury though Andrew....could have been through a knuckle or something....and on that note, I'll holler what my friend Scott hollers - AHHHHHHHHH!!!!!! :o :o :o :o :o

This is not a nail gun story although I have a few of those. I was building interior walls in an office building it was a steel stud job they were the light gauge variety instead of the self tapping framing screws we were using the regular framing screws and they are sharp little bastards when connecting a steel stud to a top track I was standing on a 2' step ladder I was talking to my apprentice the screw penetrated through the stud than screwed into the first joint of my middle finger essentially making me part of the wall and caused me to drop my screw gun so now I'm in pain with no way to unscrew myself had to wait for my apprentice to hand me the screw gun and unscrew myself no real damage just a sore finger joint for a few days :huh: Your lucky to have only 1/16" penetration most of my stories aren't that easy to listen to and by the way I only have two that are my own personal experience stories for thirty yrs of using nail guns on the job. 

One of the first things I learned about trim carpentry was when nailing a mitre joint (in a door or window casing) is NOT TO HOLD the mitre joint tight with your hand. The guy educating me said that he had lot of nail blowouts and bent nails popping out the top of the casing over the years, and he has seen many an installer with an 18 guage nail through their thumb or first finger.

First time I saw this the man operating the gun was named Brad. Another coworker had just guffawed "Watch out, that gun shoots brads." The nail hit another nail and shot out 90 degrees into his finger. Learned my lesson fast and was glad he could laugh about it. Thanks for the reminder Andrew.

I bet everyone who's spent time on a job site has a nail gun story...

 

Mine: several years ago, my Dad helped me frame-up an outbuilding... Setup the pancake compressor and Hitchi Coiled-framing nailer with 10p nails and was just about to go at it when my Dad stopped me cold... He was incensed that I was going to use a framing nailer without safety glasses - I just had on sunglasses... He'd seen a guy in his crew get a ricochet right in the face -- they guy was very lucky -- just in his cheek -- a very small scar -- but still, a cautionary tale. He made me stop, return to the shop and get the real deal...

 

I now keep a set of safety glasses in a case cable-tied to the pancake compressor...

I bet everyone who's spent time on a job site has a nail gun story...

 

Mine: several years ago, my Dad helped me frame-up an outbuilding... Setup the pancake compressor and Hitchi Coiled-framing nailer with 10p nails and was just about to go at it when my Dad stopped me cold... He was incensed that I was going to use a framing nailer without safety glasses - I just had on sunglasses... He'd seen a guy in his crew get a ricochet right in the face -- they guy was very lucky -- just in his cheek -- a very small scar -- but still, a cautionary tale. He made me stop, return to the shop and get the real deal...

 

I now keep a set of safety glasses in a case cable-tied to the pancake compressor...

I bought my first set of prescription safety glasses this year. I was also guilty of just leaving my sunglasses on, but I decided it was time to stop tempting fate. You only get two eyes in this life, and I'd like to keep them both.

  • Author

Anyone got any hints for keeping safety glasses from getting scratched? I do buy really cheap glasses, and I'm wondering if better quality ones will stand up the scratches better

Keep them on your face.  Sounds simple but, if you're like me, you take them off and toss em on the bench where they get beat up.

 

Even the more expensive glasses will get scratched on the bench.

==> I'm wondering if better quality ones will stand up the scratches better

If you are willing to spend a few $$$ you can certainly get sunglasses that stand-up to abuse, scratch resistant, impact protection, etc... I have a pair from Randolf Engineering that I use for sporting clays shooting...They have several lines of crystal-coated polycarbinate lenses -- extremely scratch, impact and shatter resistant -- but expensive...

 

I also use them for outdoor lawn maintenance -- chainsaw, weed whacking, brush cutting, etc.

 

In four years, the lenses are scratch free...

 

http://www.randolphusa.com/

  • Author

Keep them on your face.  Sounds simple but, if you're like me, you take them off and toss em on the bench where they get beat up.

 

Even the more expensive glasses will get scratched on the bench.

 

I do my best to do that, but I find I get a lot of dust on them and when I clean the lenses so I can see, the lenses get scratched then. Although undoubted they get scratched on the bench too.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.