Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Plywood edge banding bits

Featured Replies

For anyone that has these bits or is contemplating buying them, what are the pros and cons of each type? Which do you prefer and why?

 

Slot type vs. V-bit:

 

amana2_zpsf4baf9f0.jpg  amana_zpsec109c6f.jpg

 

whiteside_zps3776f9da.jpg

 

 

Thanks Chop!  I've seen these and had the same question!

  • Author

Trying to bring quality content and discussion starters to the forum ;-)

 

My two bits on the above:

 

I believe the slot version has larger gluing surface, as if that was an issue, but is more easily registered and clamped. I can see the v-bit version sliding around in the groove a bit when trying to clamp.

 

I also see the ability to sand or plane the tongue on the slotted version if you want to raise or lower the height of the band - can come in handy sometimes ;-)

  • Popular Post

==> For anyone that has these bits or is contemplating buying them

I suppose my question would be, what do the bits bring to the table?

 

I just glue-on 1/4" edging and I've never had one delaminate... I really don't care about registration because I use a trim router on the top and bottom and be done with it.

 

Is there something I'm missing?

==> I suppose my question would be, what do the bits bring to the table?

 

I guess we'd need someone who's used them to answer that. ;)

I'm with H-cubed...don't need 'em...they just make more work.

  • Author

==> For anyone that has these bits or is contemplating buying them

I suppose my question would be, what do the bits bring to the table?

 

I just glue-on 1/4" edging and I've never had one delaminate... I really don't care about registration because I use a trim router on the top and bottom and be done with it.

 

Is there something I'm missing?

This is an excellent point, for most pieces that get real wood edge banding, it is easy enough to bring to the router table to flush trim or as 3H mentioned using a handheld router.

 

So is this another tool made in search of work?

Does this router bit allow for better attachment (more glue area) of thicker/wider banding to act as shelf stiffeners?

I was talking to Todd at Whiteside about making a pair for me similar to the first ones for attaching molding plane bottoms to wooden planes.  I never got into doing that anyway, but he told me they already made some similar to my drawings for Eagle America.  If you decide you want some for some reason, I'd recommend getting the better quality ones that Eagle America sells, since  Whiteside makes them.  Their cheaper bits come from China with less of whatever grade of carbide is in them.

Save your money , they aren't all that great . I just rip my own and glue em on .  To many steps using those bites and depending on the ply you use it gets torn up . 

I always worried about clamping pressure wedging the plywood veneer upwards to increase the chance of sand through. I have found the accuracy of my Festool trim router has made edging trimming much more consistent.

Its not that its a bad idea its that there are some tools that dont do well when down sized this small. The birds mouth is a Leitz design and its fantastic when its about 4" in diameter and the stock is pressed flat with a power feeder. 

  • Author

Like the others, I just glue on the edge banding.  There is another bit for this purpose if you must:

http://www.collinstool.com/base.php?page=collins_ply_prep.htm

I have never seen that one Rick, thanks for adding. That is interesting, I never realized that the inner plies swelled so much as to cause that to be an issue. Another tool making its own market ;-)

  • 5 weeks later...

I told one of the members I would post here the next time we were setting up to run edge banding for shelves. Here is what we use, it joints the edge of the material along with cutting the profile. The top edge is self aligning and the bottom gets trimmed with a Byrd Shelix and bearing. The photo is just the initial setup test cut on scrap.

I cut a 1" wide strip of hardwood 8ft long, run the profile on both sides. Run 8ft rips of plywood for the shelves and the hardwood gets sandwiched between the two strips of ply, clamp up. Crosscut to proper length then split the two shelves down the center. Two sets can go in each set of clamps. So for 30" cabinets this makes it easy to glue up 12 shelves in just a couple minutes. With Titebond moulding and trim glue the panels are ready to crosscut, split and trim in 45 minutes.

I use the same cutter for most flat panel glue ups like shaker doors and MDF veneered slabs.

 

 

 

 

  • Author

.

 

Damn, PB!! You got some small hands :-P

 

That is an awesome way of edge banding. Very productive. Do you use a power feeder? I would think by hand would leave too much to chance since you are forming a slight line at the joint - any slackening of pressure when being fed would make this joint open up, no?

I tried that a couple of times and had too much trouble with tear out. So I just make my own edging. Did some dadoed purpleheart for the fronts of my record bins.

Damn, PB!! You got some small hands :-P

 

That is an awesome way of edge banding. Very productive. Do you use a power feeder? I would think by hand would leave too much to chance since you are forming a slight line at the joint - any slackening of pressure when being fed would make this joint open up, no?

I run everything I can with the power feeder. Officially you can run that v groover manually it's just under 5" and cuts effortlessly . My help moves the sheet down a notch and trims both sides which works fine also. It's a full face jointing cutter so it doesn't rely on the boards original edge. If you were to down size to a router bit diameter and rpm with even this cutter style you would have a hell of a time getting a good cut which is really the point. All these edge cutters need diameter to work properly. Only the long grain plys to long grain of the hard wood are where you have any joint strength. So with thin edge band there is no real expansion and contraction degradation of the joint. With thick or wide stock the worse long term joint degradation is going to be. Which is why plywood needs dados or some other form of joinery to be considered a viable glue joint against hardwood.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.