rodger. Posted December 30, 2013 Report Posted December 30, 2013 I had some walnut scraps laying around the shop awaiting a use, so I thought I would make a few Ipad holders. I looked over the internet for design ideas, and decided on a basic design that holds the Ipad at a 27 degree angle, which is good for general use on a countertop, tabletop, etc. The body of the holder is walnut, about 6" long, 4" wide, and 1" thick. I roughed out all the dimensions on my TS, and finished up with hand planes. I cut the slot for the Ipad using the TS with the blade tilted to 27 degrees, and made a few kerf cuts. After some testing, i decided that the width of the slot should be 1/2", and it should be cut 5/8" deep. I cleaned up the slot with a 1/4" chisel and some sand paper. Before I cut the slot, I drilled a 3/4" hole with a forstener bit, so that 1/2 of the hole would be eliminated by the slot. This allows the user access to the home button while Ipad is in the stand. I finished the project with shellac, and I rubbed it out with 0000 steel wool and a bit of wax to knock down the sheen. I am going to give these away to a few customers who bought multiple pieces from me this year as a "thank you" for your business kind of gift. 2 Quote
brooklyngohardwood Posted December 30, 2013 Report Posted December 30, 2013 Very cool! I love the simplicity and the finish looks great. These would make great holiday gifts and I imagine would be fairly simple to batch out. Quote
duckkisser Posted December 30, 2013 Report Posted December 30, 2013 my mom has been buying stylus for everyone for their i pads. maybe you might want to drill a hole for the stylus as well. Quote
Eric. Posted December 30, 2013 Report Posted December 30, 2013 There's a guy who buys from my hardwood dealer who makes these and says he sells them for $45. And his are really rough...dado stack tracks in the bottom of the slot, sharp corners, mill marks, completely unfinished. You could probably get $90 for yours. Quote
Rapid Roger Posted December 30, 2013 Report Posted December 30, 2013 This is interesting. I just got an Android tablet for my birthday last month and I made a quick holder for it too! I used a piece of walnut that measured 2-1/2" x 2-1/2" x 7" long. I used the table saw set at 30 degrees and a quick wipe on of BLO.so mine is a bit rougher looking. I like Ducks suggestion for a hole for a stylus too so.I'm going to drill one right now! Rog Quote
woodieboy Posted January 3, 2014 Report Posted January 3, 2014 A clever use for those pieces of wood scraps. That's a good project! That's why we don't throw out wood scraps. Quote
Countryside Workshop Posted January 5, 2014 Report Posted January 5, 2014 I got the wife an iPad mini for Christmas. I need to make her one of these. Quote
jHop Posted January 6, 2014 Report Posted January 6, 2014 There used to be a local supplier that had the plastic port protectors for the older iPods. I picked up a couple of them, with the intention of doing something similar to this. Those had a specific pattern that needed to be routed out (think extended cove), but I screwed up to ports and more scrap than I wanted to. Wish I had seen this before I spent the money on those protectors... These are fantastic! Quote
jHop Posted January 6, 2014 Report Posted January 6, 2014 . I am going to give these away to a few customers who bought multiple pieces from me this year as a "thank you" for your business kind of gift. If you could give them the gift from scrap from the purchases they made (or similar wood, so they don't think you added the extra scrap into their costs), that would be an interesting touch. Quote
rodger. Posted January 6, 2014 Author Report Posted January 6, 2014 If you could give them the gift from scrap from the purchases they made (or similar wood, so they don't think you added the extra scrap into their costs), that would be an interesting touch. I thought about doing some more with glued up scrap, kind of like an edge grain cutting board, to give the holder some more visual interest. Quote
rodger. Posted January 6, 2014 Author Report Posted January 6, 2014 There used to be a local supplier that had the plastic port protectors for the older iPods. I picked up a couple of them, with the intention of doing something similar to this. Those had a specific pattern that needed to be routed out (think extended cove), but I screwed up to ports and more scrap than I wanted to. Wish I had seen this before I spent the money on those protectors... These are fantastic! Thx! Quote
TerryMcK Posted January 7, 2014 Report Posted January 7, 2014 Nice and simple design Pug. I'm off to the shop to make one. Quote
Deadskins Posted January 8, 2014 Report Posted January 8, 2014 Great idea. Is there a purpose for hole in the back of the slot. Quote
rodger. Posted January 9, 2014 Author Report Posted January 9, 2014 Great idea. Is there a purpose for hole in the back of the slot. No, It's the remainder of the hole drilled for the home button. In future versions I may move the hole fwd about 3/16 to cut it away. Quote
Countryside Workshop Posted January 9, 2014 Report Posted January 9, 2014 No, It's the remainder of the hole drilled for the home button. In future versions I may move the hole fwd about 3/16 to cut it away. Did you drill the hole straight down or at a 45 degree angle? Quote
rodger. Posted January 9, 2014 Author Report Posted January 9, 2014 Did you drill the hole straight down or at a 45 degree angle? Straight down at 90. Quote
Countryside Workshop Posted January 9, 2014 Report Posted January 9, 2014 Straight down at 90. I'm just trying to figure out why there would only be half a circle in the middle of the wood on the back Quote
Eric. Posted January 9, 2014 Report Posted January 9, 2014 Because the dado is cut at an angle... Quote
rodger. Posted January 9, 2014 Author Report Posted January 9, 2014 Because the dado is cut at an angle... Yup Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.