Dave Posted October 11, 2010 Report Posted October 11, 2010 I bought a new Festool TS-55 and dust collector over the weekend to cut some full size sheets of plywood. Up until now I would cut the sheets down with a circular or jig saw then run them thru the table saw. The next project will have a couple of long pieces plus if my first cut is my final cut i won't have to buy a couple sheets of plywood. Considering it's cherry plywood and over $100 a sheet I didn't want a lot of waist. My plan is to cut the plywood on top of foam laying on the floor. I spent some time talking to the Festool guys at WIA and he showed me how to run the saw, change the splinter guard, adjust the play in the track and stuff like that. Any tips to help shorten the learning curve? Any must have accessories that make life easier? Quote
wilburpan Posted October 11, 2010 Report Posted October 11, 2010 I bought a new Festool TS-55 and dust collector over the weekend to cut some full size sheets of plywood. Up until now I would cut the sheets down with a circular or jig saw then run them thru the table saw. The next project will have a couple of long pieces plus if my first cut is my final cut i won't have to buy a couple sheets of plywood. Considering it's cherry plywood and over $100 a sheet I didn't want a lot of waist. My plan is to cut the plywood on top of foam laying on the floor. I spent some time talking to the Festool guys at WIA and he showed me how to run the saw, change the splinter guard, adjust the play in the track and stuff like that. Any tips to help shorten the learning curve? Any must have accessories that make life easier? The learning curve is not too bad. The splinter guard is great. Another nice thing to have is the black plastic deflector that fits over the end of the track that keeps the power cord and the vacuum hose from hanging up on the end of the track. I wound up buying the guide rail accessory pack -- it's a nice package of accessories altogether. A method that I've used for cutting sheet goods on the ground is to lay out a bunch of 2x4's flat on the ground for support. That seems to work pretty well, also. Quote
holyspidoo Posted February 8, 2011 Report Posted February 8, 2011 I keep reading about laying plywood on foam on the floor and cutting with TS55. My question is, won't the guide rail fly off? Isn't that a risk? Tx Quote
wilburpan Posted February 8, 2011 Report Posted February 8, 2011 I keep reading about laying plywood on foam on the floor and cutting with TS55. My question is, won't the guide rail fly off? Isn't that a risk? Tx Doubtful. There's a strip of rubber on the underside of the rail that generates a lot of friction. Also, you can clamp the rail to the plywood you're cutting using a special clamp that slides on the underside of the rail, if you have it up off the ground on sawhorses. Quote
Brainkite Posted December 29, 2011 Report Posted December 29, 2011 Hey guys, i offered me a TS55 for christmas/anniversary. Just got it yesterday and made a quick test on a piece of plywood. The cut quality is really there and it's amazing. Then i made a test with the bevel cut (at about 30°) and realized that the blade was eating the under edge of the splinterguard of the guide. So contrary to what promises Festool, there's still an offset when you're making bevel cuts that might be more than 1mm at 45°. That might mean that the offset is 0 when you're not using the guide rail. But what's the point? the guide rail is one of the main argument of that saw and everyone is using it. Why setting the saw for the worst case senario? (without the guide rail) Just tell me if i'm mistaking or if i'm doing something wrong but i don't understand the logic. Thank's for your help Quote
Texfire Posted December 30, 2011 Report Posted December 30, 2011 http://www.davehylands.com/Wood-Working/Knock-Down-Cutting-Grid/ I made one of these for use with my TS55. It keeps the sheets flat, even if your floor is not. And it raises the sheet goods up so I don't have to bend over the sheet. After I'm done with it, I can take it apart and get the floor space back. Finally, because there's space under the grid, I can use Dewalt clamps in the track to secure it for long cuts, though the strip under the tracks do a pretty good job of keeping it in place. Quote
Rick LoDico Posted December 30, 2011 Report Posted December 30, 2011 I use the foam on the floor to break down sheetgoods with the festool saw and rails. It's a very efficient and speedy way to go about it. The rails do not move because I always have a knee or a hand resting on the rail as I cut. Quote
ShaunHarper Posted May 13, 2012 Report Posted May 13, 2012 I just bought the TS-55 and the Panther blade. I am wondering if I should have gotten a "plywood blade". I have a Freud plywood blade for my circ saw and table saw. Very clean cut. What do others use for breaking down sheet goods? Quote
JerrySats Posted May 13, 2012 Report Posted May 13, 2012 Wow this is an old post , you just couldn't leave well enough alone huh !!! I'm being taunted by this saw , (BUY ME BUY ME ! ) It's getting harder to fight off the demons !! Quote
jmaichel Posted May 14, 2012 Report Posted May 14, 2012 I just bought the TS-55 and the Panther blade. I am wondering if I should have gotten a "plywood blade". I have a Freud plywood blade for my circ saw and table saw. Very clean cut. What do others use for breaking down sheet goods? I just built some bookcases for my wife out of plywood and I thought the stock blade left a very clean cut on the plywood edges and therefore wouldn't say that a plywood blade a necessity. I think the panther blade will be very good for ripping thicker stock. Quote
JerrySats Posted May 15, 2012 Report Posted May 15, 2012 http://www.davehylan...n-Cutting-Grid/ Hey Tex I'm thinking about building something like that plywood grid for cutting ply , did you change anything in that one or wish you did ? What did you make it out of , I was thinking some 1x stock would be better with this design then plywood . Thanks Jerry Quote
STL Woodguy Posted May 15, 2012 Report Posted May 15, 2012 I thought the stock blade left a very clean cut on the plywood edges and therefore wouldn't say that a plywood blade a necessity. Agreed, the TS55's stock blade is one of the few times I haven't run out to get a different blade on a power tool. I 'might' consider getting something with more teeth on the TS75's saw simply on the basis that the 75's stock blade apparently has less teeth, but I have no experience with the 75 and how well that does on ply (overkill for single sheets of ply, I would think). Quote
Texfire Posted May 15, 2012 Report Posted May 15, 2012 Hey Tex I'm thinking about building something like that plywood grid for cutting ply , did you change anything in that one or wish you did ? What did you make it out of , I was thinking some 1x stock would be better with this design then plywood . Thanks Jerry I started out trying to clamp the pieces together and routing out the half laps in batch so they would be identical. The problem I ran into is my bit wasn't quite long enough to plunge full length. I finished off the laps with a jigsaw and had to mess with each joint so they would slide together, sneaking up on the right fit. However after it was together, the small variances cancelled each other out and it was flush and quite rigid. As far as 1" stock vs. plywood I don't know that it would make much of a difference other than price. I had plywood so that was what I used. In addition to being a good cutting surface, it worked as a good assembly surface when covered with a flat sheet of plywood. I built it without changes, but practice one variation in use, I use bench cookies to lift the sheet being cut off the surface to avoid cutting up the grid. Quote
chicks82 Posted May 15, 2012 Report Posted May 15, 2012 Agreed, the TS55's stock blade is one of the few times I haven't run out to get a different blade on a power tool. I 'might' consider getting something with more teeth on the TS75's saw simply on the basis that the 75's stock blade apparently has less teeth, but I have no experience with the 75 and how well that does on ply (overkill for single sheets of ply, I would think). I have the TS75 and yes it does come with less teeth but it cuts amazingly smooth. It cuts ply would great both cross and rip. I planned on getting a finer tooth blade but have not needed it. It is also really nice for larger timber and the fact that you don't have to change the blade from large timber to fine cutting such as plywood is awesome. As for cutting down sheet goods I use my saw horses and 2x4s. I am not a fan of crawling on the floor do it enough already when installing base board on jobs. I am in the process of designing a 54"x102" table that has track that is similar to the track on the MFT so that you can place the guide rails and the miter accessory on the table for easy break down of sheet goods. When I get the design done I will post it so that you can take a look and see if you have any suggestions. Quote
ShaunHarper Posted May 16, 2012 Report Posted May 16, 2012 Thanx for the feedback...I will spend the money saved on not buying another blade on new chisels... Quote
davestanton Posted May 16, 2012 Report Posted May 16, 2012 This is a very handy bench that can support ply very well and is easy to transport in the back seat of a car. http://www.walko.com.au/ 2 Quote
JerrySats Posted May 16, 2012 Report Posted May 16, 2012 Dave thats a cool bench , but a little pricey at $1250 , not sure what that is in US $$ . Quote
williaty Posted May 18, 2012 Report Posted May 18, 2012 I just recently switched to the stack-o-foam method and I'm sold. I'd been trying to lift it up onto a grid, etc. No good. Found some random 4'x1'x3/4" foam panels bundled 8 to a pack for $6. Bought two bundles. Lay them 2-deep on the floor, drop the panel onto them and cut. No damage to the blade, no tearout on the back side, and actually makes the DC work considerably better. I use the included blade (wore the original out already) for cutting sheet goods of all types as well as cross-cutting hardwoods up to 8/4. I admit that *some* hardwoods at 8/4 do slow it down a bit on the cross cut with that blade. I use a new-style Panther ripping blade to rip hardwoods up to 8/4 and I've yet to get something it doesn't like to chew up and spit out and that includes ripping rock Maple. Quote
Mr. Mc Jones Posted May 20, 2012 Report Posted May 20, 2012 Check out festools owners group (FOG) lots of good info there. Also Utube has a lot of videos on the subj, lookfor Joseph Fusco, PaulMarcel, Brice Burrell to name a few of the tube folks 1 Quote
fransikaner Posted May 20, 2012 Report Posted May 20, 2012 Great referral, Dave. I watched the video and thought the Transformers had taken over the guild. Quote
davestanton Posted May 20, 2012 Report Posted May 20, 2012 Great referral, Dave. I watched the video and thought the Transformers had taken over the guild. Haha, not likely. I agree it is pricey but wow, if you are in a super tight situation or a trade on the move, this bench is a cracker and worth every cent. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.