Tpt life Posted February 2, 2014 Report Posted February 2, 2014 This is from an Auburn Tool wooden try or jointer. After chasing my tail to close a gap between the iron and chipbreaker I thought to check this. Suggestions? Quote
Bob Rozaieski Posted February 2, 2014 Report Posted February 2, 2014 Shouldn't matter. Grind the inside of the chip breaker so it seats flat. The screw should pull what's left of the bend out enough to use the plane. If the chipbreaker isn't closing tight at the tip, the problem is with the breaker. The angle behind the edge of the chipbreaker needs to be made steeper. Quote
G S Haydon Posted February 2, 2014 Report Posted February 2, 2014 I would agree C, undercut the front edge of the cap iron a bit on you stone and make that fit the blade. Quote
Tpt life Posted February 2, 2014 Author Report Posted February 2, 2014 I have 3/4 of my chipbreaker seating but one corner is gapped a full mm. The chipbreaker sits on the glass just fine. I don't see how I can adjust the breaker to the iron. Also, the iron is warped in the direction of the pull as if being tensioned to the chipbreaker is what warped the iron. Sorry if I am being thick but I still am not clear on how to do as you suggest. PS the chipbreaker has been undercut. This was my first corrective action. Quote
Bob Rozaieski Posted February 2, 2014 Report Posted February 2, 2014 Check the iron across the face. If the chipbreaker sits flat on a flat surface (i.e. the glass) then the iron must be convex across its width. The concavity you're describing along the length of the face of the blade is actually a good feature to have on a blade. However, convexity or concavity across the iron is problematic and will cause the problem you're having. That curvature across the face needs to be removed, or the chipbreaker ground to fit it (a difficult task). Curvature along the length isn't a problem. Quote
G S Haydon Posted February 2, 2014 Report Posted February 2, 2014 If the blade is bent make the cap iron fit the bend. Use a file or something like that. Finish up the last bit by drawing something hard like a bradawl across the joint between the two turning the undercut edge of the breaker over, like turning a burr. Quote
Tpt life Posted February 2, 2014 Author Report Posted February 2, 2014 Thinking about the iron as convex helped. I overhung the gappy side of the iron off the stone and worked the rest for awhile. I went back to flattening the back to one plane and the gap closed. Here is a shaving from pine. Quote
Trip Posted February 2, 2014 Report Posted February 2, 2014 ==>Suggestions? Yea, you need to find a proper glassier. Best practice -- check your plate glass for flatness prior to purchase... Quote
G S Haydon Posted February 2, 2014 Report Posted February 2, 2014 It's a full width shaving, reasonably thin, you're doing a great job. Quote
Tpt life Posted February 2, 2014 Author Report Posted February 2, 2014 I am finding it tricky to set the iron with such little experience. I was hampered for a week by part of the shaving becoming trapped under the breaker. Hopefully onward and upward from here. 1 Quote
G S Haydon Posted February 2, 2014 Report Posted February 2, 2014 You're close C, keep the faith Quote
calblacksmith Posted February 10, 2014 Report Posted February 10, 2014 If you want to get the iron flat again, it is not hard to do without grinding, I do that kind of work all the time. It is best if you have an arbor press, even one of those $15 ones from HF. You need to make a bending jig, again easy and it could even be made from hardwood not metal if you prefer that. Simply fasten two half 1" dia dowels (flat side down so that they make "speed bumps") to a base board. For this job, place them about 2" to 2 1/2" center to center apart. You need one more dowel to act as a pusher. Put your iron on a surface plate and find the highest point of the arc then place the iron, arc up (higher in the center) on the base dowels, centered between them. Put the pusher on top of the iron so as to push the iron down into the gap between the two base dowels. Apply gentle pressure and check your progress, keep at it until you are flat. You can remove twists this way too, just place the top of the twist (angled) between the dowels like you did with the high point on what you have now. Then all you will need is a light stoning to bring the iron true. Then again, if you like it bent, never mind! O ------------------------------------------------------ iron O O Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.