Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

YAYARB: Yet another yet another Roubo bench

Featured Replies

  • Author

I agree that it is a slight disadvantage, but I deliberately set the rear jaw slightly proud of the front. Given the ability to rotate the whole assembly, any warp in the piece could affect my ability to do so. In the case I want to secure against the face or leg, I'll make some shims to do so. One of the things I really like is when I have the vice rotated like in the last picture, my work is held up at a higher level, reducing if not eliminating the need for a moxon vise in the future.

There is certainly no cost savings in installing this vise.

Sent from my iPad using Tapatalk

  • 4 months later...
  • Replies 58
  • Views 14.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Do know any local auto garages well? Very useful relationship to build for woodworkers -- bearings pulled, gears/pulleys pulled, access to a powered parts washer, etc... For about $5, I'll bet they wo

  • Warren Hein
    Warren Hein

    Got a lot done this weekend. Still a few mortises to clean out after dry fitting. The tenons on the short stretchers were cut too thin for the mortises (whoops), so I'll have to glue some shims back o

  • I took some caster frames to a local powder coating shop. They blasted them and put on a tough finish and then baked it on. You would need to make sure that moving parts are not finished anywhere that

  • Author

I can now say that the bench is finished. I had been using the bench as is for a few months without the bottom shelf, sliding deadman or planing stop but finally decided to just get it all done and out of the way.

I've got to say that I love the versatility of the Emmert. I get the extra height when I want it by swiveling it 90 degrees and for various shaping tasks I've always got lots of options. About the only complaint I have is that it will rack easily if only one side is in use, so I keep scraps nearby to shim the other side of needed.

937d495a2e10ed7b01a008b398955d49.jpg

85dc550f346a2699a37f40cb2ecc28f1.jpg

I've already added some inadvertent character marks on it, but it's a bench and made to support some serious work.

065d4d6b353a47ab66e11cd0ed52e6fa.jpg

A few more final shots.

0ef5f88029ddc42f214195ae0ba47b87.jpg

7f1b307d97baa8afbb1c1ba5adebaabe.jpg

On to my next project.

Sent from my iPad using Tapatalk

Good work. Racking is always a problem with centre screw vices even the Emmert (I love that pattern makers vice - so versatile)

  • Author

Racking is actually a built in feature of the Emmett, intended to hold non-square components so the front face will always tilt to attempt to match the angle. As long as you're aware of it, it's simple enough to work around. I seem to recall there being an adjustable shim set specifically for this purpose.

Sent from my iPhone using Tapatalk

  • Author

I may eventually carve out the full circle so I can swivel the vise without first having to lift it up. In the present state, I can only have the vice in a non-diagonal orientation when it is in the down position.

Sent from my iPhone using Tapatalk

  • 4 months later...
  • Author

I'm making a shortened version of the Fine Woodworking hayrake table, and for cutting the angled tenons, I'm really digging the ability to tilt and bring the material higher up to eye level. 7102494629b3f5cecfc84310808a2742.jpg

Sent from my iPhone using Tapatalk

Nice work. That vice is tremendous and tilting is an interesting thing, makes for unlimited possibilities for work holding on things you need a different angle for. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.