Ian Gagnon Posted May 12, 2014 Report Posted May 12, 2014 Hey everyone, wanted to pick your brains for a quick second. I'm getting to a point where I'm going to be in the market for a new dado stack. Just wanted to see what everyone has been using and if they've been happy with it. I like Marc's idea of saving a few $ and going with a 6" stack. I've heard people argue that you should stick with the 8" stack because you get a higher rotational speed at the cutters and so more cuts per inch, but moving the stock a little slower can make up for that, so I'm not too worried about it. I have 2 stacks at the moment, and both are tired. One is a Mibro that was given to me and works pretty 'meh', and the other stack I bought over a decade ago, so I don't even remember who makes it (either PC or Delta). It worked great for years, but it's old and tired and no amount of sharpening is going to make it a spring chicken again. I cut dados in both solid stock and plywood, so something that's a bit of a jack of all trades is nice. I can always clean up the bottom if I need as long as there isn't too much chip out/tear out on the edges. I'll probably make a couple zero clearance inserts as well for regular dado setups I use to help in that regard. Thanks in advance for the input! Quote
CessnaPilotBarry Posted May 12, 2014 Report Posted May 12, 2014 I use a Forrest Dado King and an older Freud set. If you can swing it, I wouldn't even consider a 6" set for several reasons: - I use lots of sleds with 3/4" floors... This right here is my stopper... If you need more: - Even though I had both sets before I bought my current saw, a 6" will not work with SawStop saws. - The 8" version seems to produce better results in my eyes, when comparing identical sets in both sides. I'm not sure why, it may be the larger arc of the teeth. - The extra mass of the 8" seems to allow better feed rates. 1 Quote
Cochese Posted May 12, 2014 Report Posted May 12, 2014 Oshlun 6". I cannot run an 8" at full height, so it doesn't matter if it's better. Quote
Trip Posted May 12, 2014 Report Posted May 12, 2014 ==>I use a Forrest Dado King and an older Freud set. My exact setup... The Forrest stack is aptly named --- it's the King of stacks... The Freud stack gets used for DIY projects or when the King is out being sharpened. For small 'show' dadoes, rebates, groves, etc -- I use the Forrest Finger-joint stack -- 1/4", 5/16, 3/8", etc. Super clean for show joints... Quote
Autorotate Posted May 12, 2014 Report Posted May 12, 2014 Hi Ian, I acquired an extra 8" Forrest dado kink set with blade holder. I was told it was only used a few times, but I sent it in to Forrest to have it sharpened and checked out. They also did a test cut with it and everything is good. It still has the protective coating around the teeth they sent it back with. I listed it under the "marketplace" of this forum. I was asking $275 for it but Ill let it go for $250 if your interested in it. Bart Quote
knotscott Posted May 12, 2014 Report Posted May 12, 2014 6" stacks aren't always cheaper....don't skip an 8" just because you think a 6" might be cheaper. There are more 8" sets available, which increases the chances of finding a great deal on one. My current dado set is an Infinity Dadonator....it'd take a heck of a set to eclipse that one. The DW/Delta 7670 is a very good value at ~ $100....it eclipses all the other $100 sets I know of, plus it has a great carrying case, and excellent shim stock....not available in 6". Quote
Ian Gagnon Posted May 12, 2014 Author Report Posted May 12, 2014 Thanks for all the input! I always appreciate hearing all sides of the argument. I didn't even think about the height issue with a 3/4" sled since I don't use a sled with my dado stack, but that is a great point that leans me towards the 8".Sent from my iPhone using Tapatalk Quote
BuilderBill Posted May 14, 2014 Report Posted May 14, 2014 Depends on the budget(and what doesn't?) I've been happy with the Oshlun 8" set, just upgraded to the Freud Dial-A-Width because it's the only one I could find that would cut 7/32 grooves. I looked at the Forrest and Infinity sets but I'm tired of my drawer bottoms rattling. Just a suggestion if you do a lot of drawers with plywood bottoms.. BTW, I can make you a deal on the Oshlun set. Best, Bill 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.