Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

opinion of Grizzly

Featured Replies

I have been in residential home construction for 44 years and I am now finishing my professional career as a civilian contractor in the Persian Gulf. I plan to retire as of December 1 2015 and my retirement plans include a complete wood working shop. I have done research about tools and my present choice is Grizzly tools. This is going to be a big deal and I am trying to get as many different opinions as possible before I commit to any particular tools. So far I haven't gotten any real negative feedback about Grizzly. Any comments would be greatly appreciated.

I have a bit of their stuff and like them.  They take a little more time and patience to get set up but, typically once you get them set up they work great.  

I purchased a 14" bandsaw from them and added a riser and I like it.  No problems in the two years I have owned it.

It's always best to evaluate each tool on it's own merit.  All companies have some gems and some lemons.  With that said, most of the bigger Grizzly machinery is well regarded....much of it comes from the same factory as other Asian imports like Jet, GI, some PM, some Laguna, some Baleigh, etc.  Grizzly also has some smaller lower priced hand and bench tools that I dont' think are worth bothering with.   Grizzly's price model offers tools directly to the consumer without dealer markup, or dealer support.  They also only offer a 1 year warranty, though their customer service is excellent.  If dealer support or longer warranties are important to you, other options would be best, but if you're willing to be your own middleman, and handle the shipping and setup yourself, Grizzly often represents the best bang for the buck. They're a reputable company who sells more machinery than Jet, PM, Laguna, and Baleigh combined. 

 

I've had a Grizzly G1182HW 6" jointer since 2001, and it's been stellar.  It was rated #1 by Wood Mag over a Jet, Bridgewood, and Sunhill from the same factory, as well as over two Deltas.  I also have had a G1029 dust collector for more than 10 years that's also been flawless.  My saw is a Shop Fox W1677 that's essentially a G1023SL in white paint that's also been great.  Some years ago I made an ill-advised purchase of a cheap 3-wheel Grizzly bandsaw that wouldn't track correctly.....a common problem of most 3-wheel bandsaws.   Grizzly refunded my money for it without issue.  

I researched for a couple years approaching my TS purchase and bought a Griz 1023RLWX.  I've been nothing but happy.  The dust collection could be better but that's easy to deal with.  Turn the DC on, blow a little air from the throat plate and it gets the sawdust out of the corners- no biggie to me.  I also own a Jet 18" band saw.  it's great too but I bought it used...slightly used... for a song.  I wouldn't have considered jet as a new purchase.  Their tools are good but I just think they put too much money on the name.  So far, I have a Grizzly dust collector and a 8" sharpener/grinder.  I know with other tools, you get some more bells and whistles here and there but overall, I think Grizzly is the way to go.

  • Author

I appreciate all of the input so far.  It reassures me that I am on the right track for a good shop.  Even though I will be spending a lot of time there it isn't going to be a full blown cabinet shop and I didn't think it was necessary to spend the money on expensive top brand names.  Right now my wish list is at $10,000.00 and I plan on a trip to the factory to pick it all up and I look forward to assembling everything.  Thank you so much for your help and more is welcome. 

  • Popular Post

Consider buying the tools one at a time.  Pick a project that you want to make that only requires one or two tools (maybe shop cabinets), buy the tools necessary to make it, set them up and get them adjusted, and then make something!  Then, pick a project that needs one new tool, buy it, get it set up and adjusted, and make something.

 

I prefer this because I often find that setting up and tuning up a new tool is more frustrating than I expect, and this way I get a nice sense of accomplishment as a reward for setting up each tool.  Setting up and tuning a bunch of tools all at once can be an overwhelming drag.  

 

Also, your experiences in doing wood working projects may be useful in making decisions about what to buy.

It depends entirely on the individual tool.  I can tell you a couple Grizzly products that I own that have either serious flaws or are complete garbage (I think they actually stopped making that one).  For example, my edge sander is a good machine but they should be embarrassed by the way the table support is designed. 

I have a bandsaw and planer by them. Have had issues with the bandsaw, but I think mostly because we only use cheap blades. The planer is excellent. Plan to post a review soon.

We did pick up one of their cheap 1/4 sheet sanders, and it died within a couple weeks.

Their manuals are ok. Lacking on some things. But they do have great videos.

In general, I agree that you should judge tools individually. But yes, decently positive experience with them.

I have a few of their machines.  As the others have mentioned, it's best to judge each tool individually.  I have the following Grizzly machines (and plan to add more in the future):

http://www.grizzly.com/products/12-Jointer-w-Spiral-Cutterhead/G0609X

http://www.grizzly.com/products/15-Planer/G0453

http://www.grizzly.com/products/16-x-42-Variable-Speed-Wood-Lathe/G0632

 

All of them have been great performers and you can't beat the price.  I had one issue with the switch on my planer.  It has one of those stop buttons that click in and must be turned and released before starting the machine.   The button wasn't clicking in (not too big of a deal since the button still stopped the machine), so I called them and the tech was able to walk me through how to fix the problem.  Really friendly and helpful; probably the best customer service experience I've ever had.

The switch is one of my favorite features on the planer. Location, design, and everything. Way better than our old planer, that had a pretty stiff up/down switch.

My entire shop is Grizzly equipment. I work it very hard and have had only one problem. The starter switch on my 12" table saw quit and had to be replaced. That was after six years of using it, so I'm not complaining.

 

The best recommendation I can make is that I'd buy Grizzly again. I agree with Beachwood that you might consider buying a few pieces at a time. I bought all my equipment at one time and actually bought a couple of pieces that I wish I hadn't. I seldom use my disk sander or my planer/molding machine.

 

Grizzly does offer outstanding customer service. They are readily available if you need help while settin up your machines.

 

My one and only complaint is that I bought all my eqipment from one salesman in Springfield, Mo. I can no longer call him direct to ask questions if any arrise. I have to go through their 800 number and request that he return my call. Not very convenient for me.

 

Good luck with your shopping spree!

 

Oh, one more thing. I'm not real impressed with their drum sanders and will most likely buy a different make. Hate to bring in another color machine since ALL mine are green! That's just me. Others might have one and love it.

I have a Grizzly 14" band saw, and a floor model 6" Jointer.  I use Timberwolf blades on my bandsaw, and it is a great machine.  As long as the blade is sharp and properly tracked, I get absolutely no drift on it.  The jointer worked okay out of the box, but it did need adjusting.  I finally took the time to really get everything dialed in and got the tables coplaner.  That took me well under 2 hours to accomplish, but it was well worth it.  I will buy from Grizzly again.

I have a shop full of Griz machines and love them (Table saw, 8" jointer, lathe, oscillating spindle sander and 15" planer). My extension table and front miter bar where damaged in shipping and after a call to their 800 number I had replacements shipped to me in less than a week and they didn't make me go through the hassle of trying to ship the damaged items back. Next machine up is one of their larger band saws!

  • 2 weeks later...

My experience with Grizzly customer support so far has been great! Purchased a used G1022 Table Saw off Craigslist for $100 and couldn't be happier! I got it home and while trying to adjust the fence I snapped the clamp shoe. Even though the part has been discontinued Grizzly had some in stock and was able to get a replacement piece no problem. Called to ask about shipping and the lady I spoke with was very nice and informative. 

 

Now I'm in the process of squaring the blade to the miter slot since it's off by about 13 thousandths of an inch and the manual states to adjust the trunnions until its under 4 thousandths of an inch. Tedious to do with my model, but by no means impossible. 

 

So I love them so far! 

Just want to add this. I don't own a Grizzly machine but I've read lots of good and bad reviews about their tools and services. Their customer service is a top notch! However, many reviews said that they received their  machine with defective part/s . Just wish that it will not happen to you.

I bought my first and last grizzly product (a tenoning jig) a few months ago.

 

The casting and machining work was so poor that it was impossible, even with the adjustments at their extremes, to cut a tenon cheek parallel to the blade. It wasn't a small inaccuracy either--it was out by .100 over 10". 

 

The manual was pretty rough, and the unboxing and setup procedure was unnecessarily lengthy, requiring nearly a complete disassembly and reassembly of the jig, which, I should add, had about twice as many components as it needed to to get the job done.

 

Basically: poor design, poor qc, poor documentation, and a product that didn't even work right once. I can't believe I wasted six hours on that thing. No interest in dealing with a company like that any further.

I bought my first and last grizzly product (a tenoning jig) a few months ago.

 

The casting and machining work was so poor that it was impossible, even with the adjustments at their extremes, to cut a tenon cheek parallel to the blade. It wasn't a small inaccuracy either--it was out by .100 over 10". 

 

The manual was pretty rough, and the unboxing and setup procedure was unnecessarily lengthy, requiring nearly a complete disassembly and reassembly of the jig, which, I should add, had about twice as many components as it needed to to get the job done.

 

Basically: poor design, poor qc, poor documentation, and a product that didn't even work right once. I can't believe I wasted six hours on that thing. No interest in dealing with a company like that any further.

It seems your sample population is pretty small to write off such a large company that many speak well of.

I bought my first and last grizzly product (a tenoning jig) a few months ago.

 

The casting and machining work was so poor that it was impossible, even with the adjustments at their extremes, to cut a tenon cheek parallel to the blade. It wasn't a small inaccuracy either--it was out by .100 over 10". 

 

The manual was pretty rough, and the unboxing and setup procedure was unnecessarily lengthy, requiring nearly a complete disassembly and reassembly of the jig, which, I should add, had about twice as many components as it needed to to get the job done.

 

Basically: poor design, poor qc, poor documentation, and a product that didn't even work right once. I can't believe I wasted six hours on that thing. No interest in dealing with a company like that any further.

 

I own the same jig and agree with you about the manual.  However, I have to agree with Tim as well.  Every company makes a lemon now and then.

 

Did you return the item?  Did you call their customer service?  Did you reach out to them at all for assistance?

Grizzly sells a ton of products and within them you'll find a range of quality.  They sell low-end, poorly machined garbage akin to Harbor Freight products, and they sell higher-end machines manufactured in factories with higher QC standards.  If you buy the low-end items, you can expect low-end quality.  I would never buy "accessory" type items from them...drill and router bits, tenon jigs, etc, or their cheapest machines...but the Taiwanese machines in the higher price range in their catalog are nearly on par with with some of the more "desirable" makers.  Tim is right...you can't write off an entire company - especially one as big as Grizzly - because of one crappy tenoning jig.  No offense, but your single experience with a single insignificant item doesn't really put you in a position of authority on the matter.  It would be like me buying a set of hollow chisels from Powermatic and calling the company crap because the drill bit ran out of the chisel a trifle.

 

And FWIW...I had trouble with finding a good tenoning jig, too...I purchased and returned units from both Delta and Woodcraft before finding a good one at Rockler...made in Taiwan.  The first two were presumably manufactured in the same Chinese factory as your Grizzly.  I wouldn't make the argument that a Unisaw is a piece of junk because their tenoning jig was a piece of junk.  That's a prejudiced, knee-jerk, uninformed position.

It seems your sample population is pretty small to write off such a large company that many speak well of.

 

I'm not saying other people haven't had good experiences--I'm sure they have. I added my anecdote to the mix because O.P. requested opinions of grizzly, and I had one.

 

There's just no good reason for me to give them another chance--there are plenty of other tool companies out there.

 

 

 

Did you return the item?  Did you call their customer service?  Did you reach out to them at all for assistance?

 

 

 

Dealing with CSRs, RMAs and the like isn't how I like to spend my woodworking time (or really any of my time, at all). Especially not over a small $70 product. It was easier to just bolt on a dado stack and cut some tenons once I realized that the jig was so poorly manufactured that it would never work right.

 

A lot of people seem to have experience with Grizzly's (purportedly excellent) customer support. I see this as a negative--the best products are the ones that require no interaction with customer service reps at all. I have no idea what festool, lie-nielsen, apple, nikon, or bosch customer support is like because none of the dozens of products I've purchased from each of them have ever failed to do their job.

 

Anyways, I've made my decision and won't be buying any more Grizzly. Maybe I just got unlucky and got a lemon, but again, there's more than one tool company in the sea.

blucz,

 

Do as you will, but a reason to give them another chance is that as others mentioned their Taiwanese products (noted prominently in the tool descriptions where it applies) are good and are at a good price point.  I own one of their 14" bandsaws and am very happy with it.  Would I blindly buy anything that they sell?  No, nor would I from any manufacturer.  I research each product I intend to purchase individually.  My shop is made up of tools from many manufacturers as I try to get the best product for the money in each class.

Dealing with CSRs, RMAs and the like isn't how I like to spend my woodworking time (or really any of my time, at all). Especially not over a small $70 product. It was easier to just bolt on a dado stack and cut some tenons once I realized that the jig was so poorly manufactured that it would never work right.

 

A lot of people seem to have experience with Grizzly's (purportedly excellent) customer support. I see this as a negative--the best products are the ones that require no interaction with customer service reps at all. I have no idea what festool, lie-nielsen, apple, nikon, or bosch customer support is like because none of the dozens of products I've purchased from each of them have ever failed to do their job.

 

Anyways, I've made my decision and won't be buying any more Grizzly. Maybe I just got unlucky and got a lemon, but again, there's more than one tool company in the sea.

 

Sorry, that's ridiculous.  I can't tell you what Nikon or Bosch customer service is like but I've dealt with Festool, LN and Apple because of problems with their products.  No company is impervious to QC issues.  If you wrote off every company that ever had a problem, you'd have no one to buy from.

 

 

Girzzly really should differentiate their product lines.  Call the crap stuff Grizzly Cub or reassign shop fox to the low level stuff and accessories and save Grizzly for the good stuff.   I do think they alienate a lot of customers with their haphazard QC. 

 

That would be a great bit of advice for them to consider.  Make it clear to consumers: this one is garbage and this one is not.  They are all over the place on that, I'll admit.  That's where due diligence and research comes in, but it shouldn't be so hard to pick through their hay stack to find the needles.  I guess they're counting on a large part of their target market not really knowing the difference.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.