wouldwurker Posted January 6, 2015 Author Report Posted January 6, 2015 Thanks gang. Should I use my 1/2 sheet sander between coats? Want to get as smooth as I can since I don't have HVLP. Quote
wdwerker Posted January 6, 2015 Report Posted January 6, 2015 Be very careful near the edges and corners with a sander ! Quote
wdwerker Posted January 6, 2015 Report Posted January 6, 2015 Sand through the finish color is hard to touch up . I use a 320 grit and a cork block, carefully near edges. 1 Quote
..Kev Posted January 6, 2015 Report Posted January 6, 2015 I'd hand sand with a block between coats.. Quote
wouldwurker Posted January 7, 2015 Author Report Posted January 7, 2015 Sanded, dust removed, and second (and last, I think) coat of oil based enamel paint applied. Time to think about poly finish. Second coat of polyacrylic added to the Xmas toy chest while I was in 'finishing mode' Quote
wouldwurker Posted January 7, 2015 Author Report Posted January 7, 2015 So close to the finish line (no pun intended). Presumably sticking with oil for the finish, as was the primer and paint. My only experience with oil based poly/wiping varnish is GF arm-r-seal & GF toymakers (i.e. seal-a-cell)...which I can do well. Not sure if it will stick to the paint surface though? Regardless, I'm not bad with that particular wipe on finish technique if there's a better suited product for this particular application. No HVLP Any recommendations for my top coat(s) and/or cure time for the paint? Thanks gang --VJ Quote
wdwerker Posted January 7, 2015 Report Posted January 7, 2015 Read the label on the oil paint can, then exceed the drying time for 24 hrs at least. Quote
wouldwurker Posted January 7, 2015 Author Report Posted January 7, 2015 invest in HVLP added bonus - I can spray tan myself http://www.fujispraytan.com/ 1 Quote
wouldwurker Posted January 8, 2015 Author Report Posted January 8, 2015 invest in HVLP Done and done. You guys are bad influences. (thanks Kev and Mel) Quote
bushwacked Posted January 8, 2015 Report Posted January 8, 2015 Can't wait to see this in the position you built it for Quote
wouldwurker Posted January 8, 2015 Author Report Posted January 8, 2015 Can't wait to see this in the position you built it for Missionary Quote
wouldwurker Posted May 20, 2015 Author Report Posted May 20, 2015 Yep...this thing...that I started in April 2014...still in progress I was unhappy with the nap that the foam paint roller left on the table. It felt like painted drywall. Plus, you could see all the uneven areas once that glossy black paint was on. So I sanded the heck out of it with the Festool half sheet. So many high and low spots...all worked out. That half sheet really shines when you need to keep edges sharp and flat. Took the advice of someone (forgot who) and picked up some Penetrol for the oil based paint. I also applied it, per some forum advice with the 'roll and brush' method...roll on, even out with a high quality bristle brush. Night and Day. Between the penetrol and the foam and brush method, the paint went from this: To this One more coat and we should be good on the paint. Quote
wtnhighlander Posted May 20, 2015 Report Posted May 20, 2015 Very nice surface! I must remember the Penetrol... Quote
wdwerker Posted May 20, 2015 Report Posted May 20, 2015 The right tools, right supplies and right technique finally came together. Penetrol lets the finish flow out, used to use it back in the day. Now I use different finishes. Quote
wouldwurker Posted June 18, 2015 Author Report Posted June 18, 2015 2 coats of oil primer, at least 9 coats of oil based paint, Penetrol, one full sanding back to the mdf after being unhappy with the stipple, one final coat...followed with cat paw prints the next morning...and its FINALLY time for finish. Shooting for 4-5 coats today. Been cured about 2 weeks, so I have no worries of the waterborne over the oil paint. Let's finish this monster. 1 Quote
wouldwurker Posted June 19, 2015 Author Report Posted June 19, 2015 3 coats and foiled by the rain. Bought this can of finish today, and it was the first time I've ever seen big globs of cured goop in the can when I filtered it. Going back tomorrow for (hopefully) a free replacement. Quote
..Kev Posted June 19, 2015 Report Posted June 19, 2015 The GF High Performance? Wow.. Never had that issue with that stuff. Quote
wouldwurker Posted June 19, 2015 Author Report Posted June 19, 2015 Yeah...First time here too. Quote
wouldwurker Posted June 19, 2015 Author Report Posted June 19, 2015 Woodcraft gave me a new can, gratis. When the temp is like this...you can do 8 coats of waterborne in a day! Picked up a little can of gloss for a final coat or 2 on the top of the table as well. I'll brush that one on. Quote
wouldwurker Posted June 20, 2015 Author Report Posted June 20, 2015 DONE!!!!!!! Halla-freaking-lou-ya One year and two months from when I started this monstrosity. About 7 coats of GF high perf satin Sprayed 3 more coats of high gloss on the top only. So....who wants to help me move this thing upstairs? Quote
Popular Post Eric. Posted June 20, 2015 Popular Post Report Posted June 20, 2015 Vinny builds a giant staple! Looks good man... 7 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.