Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Giant torsion box Console Table

Featured Replies

Remember this nightmare? From April?

I vowed to not start anything new until I get all unfinished projects out of my shop. So here I am, back to the MDF nightmare.

If you recall , the 'designers' doing my living room said they wanted this:

290b03e05fc92f7fa123ce66d85a170a.jpg

4.5 inches thick, 80 inches long, and 3 feet high....and no center supports or stretchers.

Not practical or cost efficient to use that much lumber, and the forum consensus was to build 3 separate torsion boxes. So I was underway.

15ebe86e154218351fd54ad81082707e.jpge9b91f40caece3e8e8e9944ba8111e04.jpg1720a51120b4147c1ea3b7852ea7b502.jpg937ad77c7137c1e11e8513e8f8d24917.jpgc72415e4f9b7cb6f4599b567ae268dfe.jpg

204d7a075c2f7dfcfe197ad56cb8624e.jpg

I added the ruler for sense of scale.

774a0d75dec0b5d6cf14c26886a1a11b.jpg

Lots of wood putty, CA glue, sanding, mdf dust, misery, sanding, dust, hand planing, misery, dust.

Seams to fill, nail gun pops to fill, countersunk particle board screw holes to fill, sand, fill, sand, seal, sand, glue, sand, cough.

This table wasn't meant for this world.

Anyway, more sanding and filling. After all this work, I can't have a single visible flaw.

Almost prepped for 50/50 titebond and water staging. Then some oil-primer.

I can't wait to get this monstrosity out of my shop!

Sent from my iPhone using Tapatalk

  • Replies 51
  • Views 13.4k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

Posted Images

  • Author

Mostly mass and gravity. It's 10 inches deep too, and heavy and all heck. I stood on it and rocked and couldn't tip it.

Sent from my iPhone using Tapatalk

With the proper prep like you are doing that. %#€£^* stuff does paint well. I built something similar once and filled the void in the lower third of the legs with all the MDF scraps that would fit.

  • Author

8x40 dominos for a little extra ummph to attach the legs to the top. The other side 'male' end shown will be screwed into the legs.

73edb010a1e15961e3c18aa3007c67e0.jpg

eddf326ec0de47490690cfa988e06ae7.jpg

I'll also have a thin steel plate on the back hidden side, screwed into both top and legs .

Sent from my iPhone using Tapatalk

  • Author

Slathered on the glue sizing (equal parts water and titebond) on one of the legs last night. Dried clean, and feels pretty coarse. I'll hit it with some light sanding tonight and get it ready for oil-based primer.

It felt so counterintuitive to brush on a water solution to the MDF :blink: , but from the sound it, this is a tried and true method.

  • Author

Need some guidance on sanding after the glue sizing treatment, as I don't want to sand off the coating.

I had it down to 220 before I sized it and it was baby butt smooth. It's pretty rough now...feels like sandpaper actually.

Am I getting it super smooth again, or just giving it a light once over before the primer goes on?

Thanks. Really Appreciate the help...first time trying this. :(

VJ

Sent from my iPhone using Tapatalk

What finish are you putting on it?

 

I'm sure that a light sanding with 180 or 220 isn't going to take all that off.

  • Author

Oil based primer, followed by non-water based paint, followed by polyacrylic.

Thanks man

Sent from my iPhone using Tapatalk

I think you should be fine with a light sanding

You are mostly trying to seal the deeper layers and edges so with 220 grit you have quite a bit of leeway. Just be careful near corners and edges. You can sand the major flat areas until they are very smooth with little chance of harm. It's when you get near edges and corners that a moment of carelessness can be harmful. This level of caution applies to sanding between coats of sanding sealer over stain as well.

  • Author

Just wrapped up. Feels like glass. Thanks guys

Sent from my iPhone using Tapatalk

  • 2 weeks later...
  • Author

Had to break down and buy 48" clamps...ugh

Why are clamps so darn expensive!?!

983dcc5357ca9e5f76ec7717a17219a0.jpg

  • Author

...and the other leg a3841907a9a953d708e5621b1bd60c8a.jpg

I've been shimmying around this thing for weeks - I want it out of my shop!

It's like an ex-wife, some things just never go away. But, it is looking good!

  • Popular Post

It's like an ex-wife, some things just never go away. But, it is looking good!

Please... no ex wife comments.....I have more of them than I have clamps!

  • 3 months later...
  • Author

This thing again....

post-15261-14203556706606_thumb.jpg

Two coats of oil based primer applied (thanks pop!) and ready for the oil based paint.

Now, I don't have a sprayer....just using a super smooth roller, and sanded between coats with one of those spongey sanding blocks . Possibly too rough?

I still have a bit of an eggshell look now with my primer applied ....not nearly as smooth as I started after glue sizing and sanding.

Do I sand between coats of paint? If so, what should I use? Is my Festool half-sheet finish sander appropriate or overkill?

Paint by the way is 'sealskin'....an almost black gray that will be pretty forgiving.

By the way, I will be applying a poly topcoat as well.

Lastly....the bottoms of the 'feet' are still unfinished. I was thinking of just hitting it with 205 epoxy and a coat of paint after the poly has hardened.... It's too big and too heavy to flip and I'm afraid gravity will dent and knick it if i try to paint the bottoms while it's still soft. Good/bad idea?

(The paint does go all the way down btw...It's up on a MDF 'riser' in that photo for painting)

Thanks as always. This monster is that much closer to being out of my shop!

I would flip it onto a packing blanket soon and seal up the bottom quick. That way you can touch up any nicks in the paint before you use the topcoat.

If you have the epoxy use that. I would use some sort of feet , however thin or whatever just so if liquid gets spilled it can't soak into the bottom of the legs. Being able to level it could be useful if the floor is out of level and it rocks when you get it in place. Sinking into carpet can make a heavy piece wobbly, but 4 feet on each leg will be stable.

  • Author

Feet epoxy'ed last night, and first coat of oil based paint applied tonight (Sealskin).

I included a can of soup for sense of scale of this monster.

(Toybox in the back getting a topcoat)

612dcca22b386b6b30f6b10fa6d19dba.jpg

Was beginning to wonder if you were going to finish that thing  ;)   Certainly a lot bigger than I thought tho!

 

Nice job Vinny!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.