Aaron Wells Posted December 22, 2014 Report Posted December 22, 2014 Hi All, I've been woodworking for a few years and decided to purchase a 14'' Rikon bandsaw this summer. Most of the projects I've been working on did not require bandsaw work, so it mostly sat with the exception of a few minor cuts here and there. Anyway, I got a request to saw a small log in half for an arts and crafts type project. No problem I figured, I'd throw it up on the bandsaw and be done with it. I certainly didn't want to mess with a round object on my table saw. This was a pretty small piece; about 6'' diameter by 8'' length. About half way through the cut, the blade twisted sideways and got bound up, cut the plastic table insert and lower blade guide, and bent the blade. I dissected the wood piece and verified that there wasn't any metal or foreign objects in it. My question is, was what happened due to my lack of experience using the equipment and, if so, what should I do in the future to perform this cut in a better / safer way. Alternatively, is it possible that I did not set the saw up correctly and that's my issue. I followed the steps to adjust the bearings but it's possible I missed something. Quote
Coop Posted December 22, 2014 Report Posted December 22, 2014 Aaron, what size blade did you use? How many tip? Quote
Eric. Posted December 22, 2014 Report Posted December 22, 2014 Not only size and TPI, but is it the factory blade? Pitch it if yes. Are your guides set correctly? How much tension on your blade? Lots of variables... Quote
Coop Posted December 22, 2014 Report Posted December 22, 2014 And I can see that sucker rolling a bit and taking the blade with it! Quote
wtnhighlander Posted December 22, 2014 Report Posted December 22, 2014 Generally is it a good idea to use a sled or cradle arrangement to hold a round object steady while sawing. Sounds like maybe you were pushing it through freehand? Quote
wdwerker Posted December 22, 2014 Report Posted December 22, 2014 It is a good idea to build a simple cradle to hold the log straight when bandsawing it. Quote
..Kev Posted December 22, 2014 Report Posted December 22, 2014 Agree with the cradle and ditching the stock blade! Quote
Miles11we Posted December 22, 2014 Report Posted December 22, 2014 Yeah if you arent centered with the. cut and arent cutting with wood supporting all the way to the table the log may want to twist and kink to the side (grabbing the blade with it like k cooper said). Also if your feed rate is too high, gullets get clogged halfway through the cut, blade gets too hot (if it has a small set), log is green and the cut gets hot (and starts grabbing the blade), use the fence when it isnt dialed in for blade drift, unsupported cut, etc. all these thinks can cause problems major problems like that. Quote
Raefco Posted December 22, 2014 Report Posted December 22, 2014 I have the 1 1/2'hp 14"'craftsman, which is the same saw as the cheaper open bottom rikon, I love the saw and it has done a great job. I was cutting 6" walnut round stock to length and it grabbed it and bounced it off the ceiling, I was using the same 3/4" blade I was using to resaw earlier, it did not damage the saw but it did ruin the blade. I put on a smaller blade with more teeth and had no problem. Quote
Raefco Posted December 22, 2014 Report Posted December 22, 2014 I do believe a sled is in order, the saw was cheap and it did not come with a miter gauge or rip fence, I ordered a rikon fence Set up for it but I have not got a miter guage that fits the slot properly. Quote
AceHoleInOne Posted December 22, 2014 Report Posted December 22, 2014 I think the wood shifted/turned while cutting and the blade had a catch. Plus one to what everyone is saying about the piece you're cutting needs to be held secure during the cut! I had a similar thing happen while free-handing an odd shaped piece. Sorta was like a kick-back and bend the blade. -Ace- Quote
woodieboy Posted December 23, 2014 Report Posted December 23, 2014 I believe you were feeding the wood too fast or the blade was under tensioned. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.