Mzdadoc Posted December 28, 2014 Report Posted December 28, 2014 Today is fine tune day. Just a quick question on the fact I'm making tapers with my jointer instead of straight flat edge. Is this need for more proper set up or how I'm feeding and where I'm putting pressure? Quote
rodger. Posted December 28, 2014 Report Posted December 28, 2014 Well, it kind of depends. If you are jointing a rough board, the jointer has no idea what the other edge or face is like. Your taper could be the stock being irregular. To be sure, take a flat and square board and joint it. This should help identify the issue. Many times its user error, but not always. Quote
..Kev Posted December 28, 2014 Report Posted December 28, 2014 Pug is correct Doc. The Jointer is only to make a flat side. The planer will make the other side parallel to the jointed side. Quote
Mzdadoc Posted December 28, 2014 Author Report Posted December 28, 2014 Well I was jointing a 2" x 2" x 24" It's a turning blank that I was going to make candle holder legs with. I just wanted to clean a couple sides so I could rip it 1 1/2" x 1 1/2" I now have one tapered leg. Quote
..Kev Posted December 28, 2014 Report Posted December 28, 2014 Something had to be out of parallel when you started. The jointer is just not designed to take a heavier cut at one end than the other. Quote
Tpt life Posted December 28, 2014 Report Posted December 28, 2014 Bad jointer setup can do this. If your outfeed falls away from the cutter, the board can rock and the trailing edge of your board will never be as deeply cut. Re-verify the jointer tables. 1 Quote
..Kev Posted December 28, 2014 Report Posted December 28, 2014 Bad jointer setup can do this. If your outfeed falls away from the cutter, the board can rock and the trailing edge of your board will never be as deeply cut. Re-verify the jointer tables. This is correct, I was assuming a properly set jointer. 1 Quote
Mzdadoc Posted December 28, 2014 Author Report Posted December 28, 2014 Kev never assume a properly set jointer. It is me ya know.... Quote
Mzdadoc Posted December 28, 2014 Author Report Posted December 28, 2014 I set up the outfeed table to be exactly the height of the cutters but I'm suspecting I'm pushing to hard down on the outfeed end Quote
Tpt life Posted December 28, 2014 Report Posted December 28, 2014 Setting the outfeed table the height of the cutter only references one end of the table. You want the whole outfeed as close to coplaner with the infeed as possible. I am not suggesting merely raising or lowering but potentially shimming etc. does your jointer use dovetail or parallelogram? Quote
Mzdadoc Posted December 28, 2014 Author Report Posted December 28, 2014 Ok now I understand. I was just checking nearest the cutting head. Not sure which as far as dovetail or parallelogram. Where would I look? Quote
Tpt life Posted December 28, 2014 Report Posted December 28, 2014 Dovetail ways leave a base that looks triangular under the tables. As you raise and lower the tables they slide along the slope. Quote
Tpt life Posted December 28, 2014 Report Posted December 28, 2014 Have you run a straight edge across the tables? If they are not true then creating coplaner setup involves shimming the ways. How much have you used the jointer. Can you say things have changed or is this your first few passes? Quote
Beechwood Chip Posted December 28, 2014 Report Posted December 28, 2014 You want to watch Marc's jointer tune-up video. With a dovetail jointer you may need to use shims where Marc could use adjustment screws. Quote
wdwerker Posted December 28, 2014 Report Posted December 28, 2014 Even with a perfectly set up jointer it takes some practice to use it right. Practice using fairly light cuts on cheap stock or scrap. Infeed and outfeed coplanar is the first thing to check, then cutter head to outfeed, at least that's how I do it. How you shift the pressure as you joint a board can affect the cut. Quote
wtnhighlander Posted December 29, 2014 Report Posted December 29, 2014 Maybe obvious, but did you try to joint with a covex side toward the beds? I find it almost impossible to get a straight cut unless I put the concave side down. Quote
Mzdadoc Posted December 29, 2014 Author Report Posted December 29, 2014 Yes I use the jointer frown down. I put a level on each bed and they are exactly the same point of level or is that not a great reference. I'm going to spend more time in it tomorrow. Even if I joint a flat piece I taper it. Quote
dwacker Posted December 29, 2014 Report Posted December 29, 2014 Yes I use the jointer frown down. I put a level on each bed and they are exactly the same point of level or is that not a great reference. I'm going to spend more time in it tomorrow. Even if I joint a flat piece I taper it. Its easy to put to much pressure on the the piece as it enters the cutter "frown down". Run your leading edge into the cutter with pressure against the fence. If there is a good sized "frown" Cut the leading edge, stop and lift off the cutter turn around and hit the trailing edge. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.