Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

MDF not the best router table top after all?

Featured Replies

None of my router plates are screwed down. Just the weight of the router holds it in place. On my oldest router table I used layers of tape to shim the plate flush to the surface. Still works fine after a couple of decades.

I went to a local reclaim store and bought a piece of corian counter top. I cut it to size with my tablesaw. I then laminated three sheets of cabinet ply together. All this mounted to the extension table of the saw.

 

post-497-0-66091900-1419885574_thumb.jpg

I'm thinking of laminating two slabs of MDF sheets together as well.  I can't think of a good clamping method of laminating two such large pieces except prepping, gluing, and parking my truck tire on top of the two pieces overnight. *banjos twang in the background*

Screw the pieces together. You just have to be careful and place the screws where you won't hit them later. 

I just used yellow glue for the plywood laminate. I used two part epoxy to set the plywood to the Corian.

 

 

How did you do the lamination MikeD?

I have been away from the forum for a few days being sick, so I am just now getting caught up on some of the older posts.  I have at this point built two router tables, both from 2 layers of MDF.  The first top was 3/4" and 1/2" MDF layered together, then second top used 3/4" for both.  I glued and screwed them together and then squared up the whole thing after the glue dried.  Both tops were then edge banded with a hard wood, whatever I had laying around.  The the last step a layer of formica on the top.  This has made a real nice surface for my router table tops.  The first one lasted me 9+ years and is still flat.  The second one I built this past spring.  I designed the table base to support the top to help prevent sag.  

 

On both tables an opening for the router plate was routed in so that the plate fit in snug.  The newer table I put a lift in and the incra plate on it has an addition screw to keep a snug fit between the table and the plate.  No issues with vibration.

 

As much as I hate working with MDF, I really like it for a router table top, largely because of the weight.

  • Author

I have been away from the forum for a few days being sick, so I am just now getting caught up on some of the older posts.  I have at this point built two router tables, both from 2 layers of MDF.  The first top was 3/4" and 1/2" MDF layered together, then second top used 3/4" for both.  I glued and screwed them together and then squared up the whole thing after the glue dried.  Both tops were then edge banded with a hard wood, whatever I had laying around.  The the last step a layer of formica on the top.  This has made a real nice surface for my router table tops.  The first one lasted me 9+ years and is still flat.  The second one I built this past spring.  I designed the table base to support the top to help prevent sag.  

 

On both tables an opening for the router plate was routed in so that the plate fit in snug.  The newer table I put a lift in and the incra plate on it has an addition screw to keep a snug fit between the table and the plate.  No issues with vibration.

 

As much as I hate working with MDF, I really like it for a router table top, largely because of the weight.

 

I appreciate you sharing your expertise.  Every day that passes and every reply to my various question topics gets me one step closer to the final design of my own new table.  All the suggestions from all the experts here, rolled into one tasty new table.

 

I'm glad to hear you're feeling better.  Now if I could just get over my own nasty cold...

  • Author

I don't usually link back to my blog for these posts, but my entries on my recent router table build may benefit you.  I went all out for this build and the table is an absolute joy to use. 

 

http://sawdustnewbie.com/category/projects/2014/router-table/

 

Thank you for sharing this!  The designs that have been shared in this topic all look wonderful and give me great ideas.

My $.02...These:

 

http://www.rockler.com/router-plate-leveling-and-locking-hardware-pack-for-custom-router-table-tops

 

I have the Rockler router table top (that I have modified to fit my setup.  It has an MDF core and high pressure laminate.  Those puppies keep the plate on like a charm.  And if the threaded inserts pop out ever, nothing Titebond cant fix.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.