Mzdadoc Posted March 4, 2015 Report Posted March 4, 2015 The retired principle of my kids school just bought a brand new saw that doesn't work. Here's what I know it's a Craftsman about $600 and 300 lbs and when you plug it in (110) the motor hums but doesn't spin. He's called their help number but of coarse as expected they told him to bring it in to a service center. Any help or ideas would be greatly appreciated!!! Thanks Quote
knotscott Posted March 4, 2015 Report Posted March 4, 2015 The first thing I'd do is remove the belt to find out if something is binding. Once the belt is removed, start the motor... if the motor still won't spin, return it to where it was purchased from....there's something wrong with the motor. If the motor does spin once the belt is removed, check that the belt is seated properly and the arbor spins freely. If this was some sort of special clearance deal that can't be returned, check the capacitors on the motor...if those are good, check the centrifugal switch. Either way, it should be covered under warranty. Quote
woodbutcher74 Posted March 5, 2015 Report Posted March 5, 2015 I would assume the motor is wired for 110VAC? He didn't change the cord or anything? If it's wired for 220VAC, that would explain a lot. Just and thought. Quote
Mzdadoc Posted March 5, 2015 Author Report Posted March 5, 2015 That was the first thing I asked was about the wiring. 110 and he didn't do anything with the power cord. Quote
Greenaqua Posted March 9, 2015 Report Posted March 9, 2015 I tried plugging my 110tablesaw to a outlet that didn't provide adequate amperage one time and it did the same thing. It wouldn't even spin the blade. Quote
ponderingturtle Posted March 9, 2015 Report Posted March 9, 2015 I tried plugging my 110tablesaw to a outlet that didn't provide adequate amperage one time and it did the same thing. It wouldn't even spin the blade. It should have popped the breaker then. Is the motor not spinning or the blade? Quote
wtnhighlander Posted March 10, 2015 Report Posted March 10, 2015 On single phase AC motors, the 'no-spin, no-trip' symptom can happen if the starting cap is bad, or a shading pole is open, whichever motor type you have. Quote
Greenaqua Posted March 10, 2015 Report Posted March 10, 2015 It didn't pop the breaker, it was a 14 gauge wire that ran about 150' to my detached garage and the receptacle was there for the automatic garage door opener. The breaker was 15 amp. I don't live there anymore so it's not an issue for me. This was on a craftsman 22124. Once I had adequate voltage or amperage to my saw with new wiring it ran just fine. The blade wasn't spinning but don't think the motor would be either Quote
Trip Posted March 10, 2015 Report Posted March 10, 2015 ==>14 gauge wire that ran about 150' There are volt/amp/gauge/distance tables extracted from the NEC and posted on the web (please look for the NEC label on the table or something like Electricians Toolbox -- don't trust Joe-DIY tables for things like electric)... That's a good place to start when distances get to say 35' and over... Probably not applicable to the problem at hand, but you never know -- that 150' 14g extension cord is a classic... Back to the original problem: Could be a few things… Most already mentioned... Unfortunately we don’t know the type of motor… Can you get a model for the saw or (even better) a photo of the plate attached directly to the motor? We really should start there... For instance, it could be a dual-voltage motor simply wired for the wrong voltage... Simple right -- but only if we know the type of motor... Quote
Mzdadoc Posted March 13, 2015 Author Report Posted March 13, 2015 Sorry guys the whole family of six has been battling Influenza B and it sucks! Thanks for all the ideas and I'll try to get more info. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.