SawDustB Posted July 8, 2015 Report Posted July 8, 2015 Hi guys, I recently acquired a new to me miller falls block plane (number 16) from eBay. It seems to be in good shape, but I feel like I'm missing something. The mouth will only close as shown in the picture: And this is with the mouth open: I thought the point of the adjustable mouth was to have it really small (1/32) when taking a fine shaving. This is only getting down to 3/32 or so. Please tell me where I'm going wrong here. Sent from my Nexus 5 using Tapatalk Quote
Tpt life Posted July 8, 2015 Report Posted July 8, 2015 Is the blade set to cut in your picture? The blade will fill much of the 3/32. Quote
SawDustB Posted July 8, 2015 Author Report Posted July 8, 2015 Yes, in my pictures the blade is set to take a fine shaving. I can't see any sign that someone filed the mouth, and all parts seem like the correct ones. Sent from my Nexus 5 using Tapatalk Quote
Tpt life Posted July 8, 2015 Report Posted July 8, 2015 Just checking. I have the Stanley and Record versions which will both choke the iron right down. I'd disassemble the nose and inspect the inside of the motion. Quote
SawDustB Posted July 8, 2015 Author Report Posted July 8, 2015 Sure, I'll pull it apart again and post a picture when I get home later. I took it apart yesterday, but couldn't see any issues. It seems to move OK, and aside from a bit of surface rust there is no obvious defect. When the knob is loosened, I can move the lever for adjusting the mouth through its full range of motion and tighten it down anywhere along it. I'm struggling to figure out what's wrong - what you're describing for your other planes is what I had expected. Aside from the fact that I'm reasonably sure the mouth should be able to be closed more, it all looks fine. Quote
weithman5 Posted July 8, 2015 Report Posted July 8, 2015 I think i have this very plane. i will check when i get home tonight. Quote
SawDustB Posted July 8, 2015 Author Report Posted July 8, 2015 I think i have this very plane. i will check when i get home tonight. Thanks, that'd be awesome. Sent from my Nexus 5 using Tapatalk Quote
Tpt life Posted July 8, 2015 Report Posted July 8, 2015 Yep, it appears the Millers Falls No. 16 has a very open mouth. I get a 1/16 to 1/32 shaving clearance at its tightest point. Just found I have one in a recent CL group purchase. Quote
SawDustB Posted July 8, 2015 Author Report Posted July 8, 2015 OK, thanks. I guess I just use it as is, then. That seems like it defeats the purpose of having an adjustable mouth. Sent from my Nexus 5 using Tapatalk Quote
Tom King Posted July 9, 2015 Report Posted July 9, 2015 Take the front screw/knob all the way out, drop the sliding piece out, and see if there's something in there that shouldn't be. You might even see a way to modify it so it can close up tighter. I would even take the adjuster cam off it that would help, if it was mine. I almost never use a block plane with an open mouth. 1 Quote
weithman5 Posted July 9, 2015 Report Posted July 9, 2015 mine is a millers falls 56B the smallest mouth i can get is 1/8 inch maybe just under Quote
SawDustB Posted July 9, 2015 Author Report Posted July 9, 2015 I tried your suggestions Tom, and the casting itself will allow the mouth to close up to just over 1/32. It looks like I could get it to close all the way if I wanted to do a little bit of work with a file, but I'm assuming that I wouldn't want or need much closer than that anyway. The adjuster cam is the real problem, since it's preventing the mouth from closing up below 3/32. I may see if I can put a bend in it to shorten it. If not I'll probably just take it off. Quote
Tpt life Posted July 9, 2015 Report Posted July 9, 2015 You know, my little guy is so old there's a chance someone used an adjuster from a different family of planes. Just got me thinking. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.