Recommended Posts

Posted

Hello everyone!

I just got into woodworking about a year ago doing dome small projects with a drill, a Jig saw and a couple of hand tools.

About a week ago I bought a brand new  Delta Bench top Table  saw. I've been doing some test cuts, and of course the frustration started LOL.

My cuts have been somewhat inaccurate even though I have tried to align the saw with much care.

My question to you guys would be, Did I make a mistake buying such a cheap Table saw? How accurate can I expect a Bench top Table  saw to be?

Thanks in advance guys!

 

P

 

Posted (edited)

Welcome to the forum!

Accuracy is relevant to the projects you are wanting to accomplish and the standards you are comfortable with. What is acceptable inaccuracy in a project - over the span of what length? For some, that may be 1/8", 1/16", 1/32", 1/64", or even less depending on their own standards and length. 1/8" over 12" is a big deal whereas 1/32" over 16 feet is not as much. More expensive and dedicated cabinet-grade saws are, broadly speaking, more accurate in their cuts because they remove some variables from the equation that smaller saws have. 

If the saw is already frustrating you, I think you know the answer to the question. That being said, there are steps you can take to improve the accuracy of the saw - some are free, some cost money. For free, take some time to go over the manual on ensuring everything is aligned to everything else (blade-table alignment, fence-blade alignment) and take it from there. If you still encounter frustrations, then you may want to examine your return options and save some cash for a more serious machine.

The table saw is often the heart of the shop, and I would surmise that many would advise to spend as much as you can reasonably afford since it will be performing the bulk of your tasks. For serious woodworking, the jointer and planer would be next on the list.

Edited by Al Capwn
  • Like 1
Posted

What do you mean by innacurate?  

Do you mean that your cross-cuts are not square or that your rip cuts on not parallel?

Or do you mean that you are not getting the dimensions you want?

I ask by I am trying to understand if it is the machine or a problem with your technique.  

Posted

Does the board you are ripping have a jointed edge?  If its "off the shelf" lumber, there is a good chance that the edge is not true and this could be causing your issue.

Posted

Does the board you are ripping have a jointed edge?  If its "off the shelf" lumber, there is a good chance that the edge is not true and this could be causing your issue.

Yup. This is my guess. 

Posted

Well i dont have a Jointer or planer. But even though the side i'm using for reference was not joined it looked pretty straight. But you'r right maybe I should try to get a perfect side before I return the machine! Lol

Thanks gain guys

I'm wating for a dial indicator that i just ordered to make sure that i make the alignments to the .001's of an inch.

Posted

Well i dont have a Jointer or planer. But even though the side i'm using for reference was not joined it looked pretty straight. But you'r right maybe I should try to get a perfect side before I return the machine! Lol

Thanks gain guys

I'm wating for a dial indicator that i just ordered to make sure that i make the alignments to the .001's of an inch.

This hobby can get expensive, can't it?

Posted

Not as expesive as being a guitar player but yes. The toys!!!

As a novice Woodworker i would like to ask you guys if there is anything that you consider a "Must", meaning a book, website, a youtube channel, etc., so i can save some frustration in the future.

thanks yet again!

Posted

Not as expesive as being a guitar player but yes. The toys!!!

As a novice Woodworker i would like to ask you guys if there is anything that you consider a "Must", meaning a book, website, a youtube channel, etc., so i can save some frustration in the future.

thanks yet again!

As a guitar player, woodworker, and all around over enthusiastic hobbyist, I can confidently say that my tools cost way more than all of my guitars in my music room. This hobby doesn't end. Tread lightly, and dive right in! Good luck in the endeavor, and ask questions along the way.

  • Like 1
Posted

Not as expesive as being a guitar player but yes. The toys!!!

As a novice Woodworker i would like to ask you guys if there is anything that you consider a "Must", meaning a book, website, a youtube channel, etc., so i can save some frustration in the future.

thanks yet again!

Patience.

Even with all the available knowledge this is still a hands-on practice and technique develops slowly. It's all built around your choice of equipment, wood, and projects. It's far from an exact science.

Like playing guitar, my skills improved significantly once I learned to keep my thumb on the back of the neck rather than wrapping it around.  It took a lot of *time* to build up finger strength but it was worth it.  But like woodworking it's a hands-on experience. 

I've only been at it for a little over a year (with winter subtracted because my garage is not heated). So no very long.  Also started with one of those bench-top saws. I found its biggest weakness was the shallowness of the cutting surface.  Without a long fence a board can drift and that contributes to inaccurate cuts.  A "contractor" type saw is a minimum, imo.  And they can be put on wheels to be rolled around.

Posted

Depending on which way you swing, you could consider getting a No. 5 jack plane.  It (can be) a heck of a lot cheaper than getting a jointer and it can take care of just about any milling you might need to do (at least until you go further down the rabbit hole and decided that you need a smoother, a jointer plane, a block plane, a dado plane, a scraper plane, a rabbet plane...oh god it never ends...make it stop...I need them all...).  If hand tools aren't your bag, then any good lumber yard will joint one edge for you, usually for a small fee.  

If it's not the stock, then I'd bet your problem is the fence.  Even properly aligned, the stock fences on bench top saws are usually too insubstantial and have too much play when locked down.  Best upgrade you can make is to get a good aftermarket fence.  I use my grandfather's late 1940s/early 1950s craftsman table saw.  I was having a heck of a time getting accurate rip cuts, because the stock fence was crap.  So a few years ago I bought a Vega Pro fence, and ever since my rips cuts have been dead on accurate.  Also, getting a microjig gripper will help immensely with ripping thin stock like the 3/4" rips you were making.  Not only will it be safer, but more accurate as well. 

Posted

 Also, getting a microjig gripper will help immensely with ripping thin stock like the 3/4" rips you were making.  Not only will it be safer, but more accurate as well. 

 

My thumb can attest to that. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined