trialbyfire Posted January 19, 2016 Report Posted January 19, 2016 Sooo I'm sharpening my first set of chisels and I'm at the point of putting the micro bevel on. I'm using the Veritas MKII and have come up with a skewed micro bevel. Am I doing something wrong? Quote
Llama Posted January 19, 2016 Report Posted January 19, 2016 33 minutes ago, trialbyfire said: Am I doing something wrong? Yes. You are probably over tightening the jig, or putting un-even pressure on the roller. Or both. Quote
Tony Wilkins Posted January 19, 2016 Report Posted January 19, 2016 13 minutes ago, Llama said: Yes. You are probably over tightening the jig, or putting un-even pressure on the roller. Or both. Which is easy enough to do with this jig. It's its one main drawback. Quote
shaneymack Posted January 19, 2016 Report Posted January 19, 2016 Make sure it is square in the jig and apply even pressure. Before you get as far as you did check your progress. A couple swipes, check, adjust pressure and continue. Sent from my SM-N910W8 using Tapatalk Quote
rodger. Posted January 19, 2016 Report Posted January 19, 2016 Yup, agree with above. Plus, narrow chisels are tough to get right without some practice. You may have better results with a wider chisel or a plane iron. Quote
trialbyfire Posted January 19, 2016 Author Report Posted January 19, 2016 OK so I changed my approach. Instead of applying pressure to the jig with both hands I put both index fingers on the chisel itself to apply the pressure. This seems to be leveling out the micro bevel. Thanks y'all. Another question, I understand that the micro bevel is to decrease the amount of time and effort in sharpening the chisel but is there a "golden zone" on how far up the bevel the micro bevel goes? For instance, if the micro bevel is slightly larger, would it have less resistance when paring or chopping than if it had a smaller micro bevel? Quote
shaneymack Posted January 19, 2016 Report Posted January 19, 2016 I do mine at about 1/32". If you make it much bigger you are just making a primary bevel again. Like you said it's there to facilitate future sharpenings so small is key. Sent from my SM-N910W8 using Tapatalk Quote
trialbyfire Posted January 19, 2016 Author Report Posted January 19, 2016 How important is it that the micro bevel be square to the edge? I mean its not going to cut less effectively of the micro bevel is slightly skewed is it? Quote
TerryMcK Posted January 19, 2016 Report Posted January 19, 2016 As long as the edge itself is square you are good to go. Skewing of the microbevel relative to the main bevel is not a problem. In the latest manual for the MKII (have a look on the Veritas website to download it) Veritas have an explanation. Anyway you appear to have it under control now. On your other question "how far can you go with the micro bevel?" you can go all the way up the main bevel. At which point regrind to re-establish the main bevel and start again. Quote
ponderingturtle Posted January 19, 2016 Report Posted January 19, 2016 3 hours ago, TerryMcK said: As long as the edge itself is square you are good to go. Skewing of the microbevel relative to the main bevel is not a problem. In the latest manual for the MKII (have a look on the Veritas website to download it) Veritas have an explanation. Anyway you appear to have it under control now. On your other question "how far can you go with the micro bevel?" you can go all the way up the main bevel. At which point regrind to re-establish the main bevel and start again. In principle one of the bevels would have to be out of square. Of course it gets into issues of how square is square, are we talking about a tollerance of a degree or is it measured in arc seconds(those would never matter for woodworking) Quote
Tom King Posted January 19, 2016 Report Posted January 19, 2016 It's a common problem, especially with that jig. I used to use microbevels back when I only had oil stones to use. Relative to today's good waterstones, an oil stone is VERY slow. Not to say you can't get a great, sharp edge, but very slow by comparison. Without doing a microbevel, it would take a L O N G time from start to finish with oil stones. While in a job that requires frequent honing, and having gone through several upgrades in water stones to ones that are very fast, my microbevels got larger to the point of taking over the whole bevel. Somewhere in that process, the need for microbevels disappeared. Now I just hone the whole bevel, and no tricks on the backs either other than flat. Having more stones in the progression speeds the whole process up by requiring fewer total strokes, but if you stop working when you only need to go back a stone or two from the finest, microbevels are just extra bother. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.