Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Breaking blades on the Knew concepts fret saw

Featured Replies

I have the red aluminum 3 inch fret saw with the angle detents and the tightening lever.  I watched a few videos and loaded up another Pegas blade (bought a pack with my saw). As before, it broke after the third or forth dovetail waste I sawed.  I'm not sure what I'm doing wrong - too tight, too loose, sawing too fast?

 

any suggestions?

hmm, that is odd.  I've had about a year and never broken a blade. I know that doesn't help you much!

Things I can think of:

  • Maybe you're forcing the saw too much? Let the blade do its job, etc.  I hardly put any pressure on it.
  • I did also find the installation and tensioning to be super fiddly at first, even though it looks super easy on the videos.  I ended up just finding a sweet spot for tension that seems to work for me and haven't played with adjustments at all since.  Not really looking forward to when I need to replace the blade!
  • The blade being seated right seems to be really important on this saw, I did have some initial troubles getting it inserted correctly (it was coming loose on me) - so maybe that is worth look at too?  

Hope this helps, good luck! Once you get the baby working, it is awesome

 

I hope you get it figured out. I would be pissed if a $6 HF saw works better than my $150 one

  • Author

Went back, watched a different video of it.  Went and did a post mortem on the blade and thought about it,. The blade didn't break so much as it came loose from one end and kinked in a dramatic fashion. I wondered if I didn't sink it deep enough on both ends.  New blade and tried to make sure this time they were set deeply in the end sockets.

I don't have a knew saw yet but I try to keep the stroke speed up and the feed rate very light. Let the teeth do the work , not your pressure. Especially keep the speed up and cut rate light when turning a sharp corner. I can spin the frame 180 and never really feed the blade in any direction just by keeping a steady pace with my strokes.

Next job that needs plenty of cope cut joints I'm getting me a Knew saw.

  • Author

Thanks Steve.  I should point out I reckon that this is my first time using a fret saw (nor have I used a coping saw.)

I have a jeweler's saw and several coping saws. The fine blades for the jeweler's saw snap easily but come 2 dozen to a pack. You can get the tension almost piano string tight, goes ping when you pluck it. Throat is only about 3 1/2" deep

There is no plate to keep your stroke in plane. You have to have a practiced stroke first. I am not implying you don't, just starting back at the easy to bypass. If you are going to bind a blade with "out of plane motion", this is one of the easiest. I will sometimes cut on the pull with a cope saw if the angle is funny because this can lessen the chance of getting off plane for me. 

Hi Tony! What wood are you cutting and how thick? A coping is more robust and saw might be better suited to waste removal. Keep the fret saw for fret work ;-) https://www.google.co.uk/search?q=575+wandsworth+road&source=lnms&tbm=isch&sa=X&ved=0ahUKEwizpNH-06DLAhXKBZoKHWpLAQgQ_AUICCgC&biw=1366&bih=667#imgrc=hHINDYxh2Q_dEM%3A

  • Author

@C Shaffer I definitely don't have a practiced stroke so I'll keep that in mind.

@G S Haydon I'm cutting Borg 1x12 white pine so it's not too tough.  I've seen folks using this saw for this purpose so it should be possible.

Agreed Tony, should be ok, keep practicing. I personally have never used a fret saw and would still favor a coping saw for the job you're doing, even a basic cope would be fine. I'd assume that with such a fine blade in a fret saw you'd be cutting on the pull stroke?

  • Author

I am using it on the pull stroke btw :)

 

I have been sorely tempted to find the Olsen coping saw I bought my oldest a while back.

I have the Knew Concepts Coping saw and I am all too regularly snapping Pegasus blades with it.  These tend not to be kink-breaks, just explosive...."oh look, half of the blade is over there now" sort of breaks.  I use the saw on the pull stroke as I think it is easier to control.  I really like the saw and even with the exploding blades it is drastically better than the buck bros POS that I upgraded it from.  I'm one tail board into building Shannon's saw till and I'm on my second blade already.  I was going to blame the blades, but now I'm not sure.  Too much tension?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.