Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

exhausting DC outdoors - its what all the cool kids are doing

Featured Replies

how do you determine the size of your exhaust port? I have a single stage dc, which i can turn into a 2 stage by purchasing a super DD.

My intake is 5". should my exhaust match the intake? should it be larger? does it matter?

obviously, the single stager will require some modification to turn the 20" hole into a smaller one, but that should be no problem with some pywood, gaskets, and some creative thinking.

i need to drill/ core this hole through the sidewall of my garage, which is venerred with stone.  will require the rental of one large-ass drill, as well as a core bit. i really only get one shot at drilling the hole if i do this, so i would like to make sure its the appropriate size.

If you can't find a large enough core bit to rent, for such jobs I buy cheap 4-1/2" grinders, diamond blades, and have a helper blow the dust away with a leaf blower.  For stone, I have a helper hold a water hose with a small stream of water to wet the blade, which does away with the dust.  The other, quicker helper holds the plugs.

I have cut holes using a hammer drill and a cheap auto body type air chisel. I drilled a circular pattern of holes with the hammer drill and then chipped out the center with the air chisel. Slow, dusty and noisy sure but it was cheap and worked. 

Yep..  Chain drill with smaller diameter masonry bits and then tap out with a chisel.  You'll still need a decorative flashing but, should look neat and clean when finished. 

  • Author

i can rent all i need from the local hd - they have large drills and core bits. i just dont know whst size hole i need. did some looking online, but to no avail.

  • Author
52 minutes ago, Tom King said:

If you can't find a large enough core bit to rent, for such jobs I buy cheap 4-1/2" grinders, diamond blades, and have a helper blow the dust away with a leaf blower.  For stone, I have a helper hold a water hose with a small stream of water to wet the blade, which does away with the dust.  The other, quicker helper holds the plugs.

wheres the best place to start the drill, tom? in the centre of a brick, or in the mortar?

1 minute ago, C Shaffer said:

Check the rock. It might work to just pop one off. 

huh?

  • Author
1 minute ago, C Shaffer said:

You said veneered with stone. I have pulled a couple hundred stones off homes to set exhaust fixtures in my past. 

the veneer is manmade stone, and each "brick" is approx 10"x3"x3".

For what it's worth I have a diamond impregnated circ saw blade. I will rough in an outside margin and then drill a series of holes with a standard masonry bit. I have never gotten around to buying a coring bit. It is a good way but takes expensive bits. 

I would start with a 1/4" or similar size bit and drill all the way through.  That lets you shift the center if the inside or outside locations have problems. I would make the hole in the foundation & rock veneer about 1" larger than the pipe. It is far easier to foam the gap than to enlarge the hole.

I would drill several holes with a masonry bit and then chisel out.  I also agree with Steve that going bigger is easier than having to remove more.

Just hammer drill a small pilot hole to start with where you need it. It shouldn't matter of which surface-mortar or stone.   If you could do a square cap over everything, it would be a lot easier cutting the hole.  I've never bought any core bits either, but do have one bit that I can drill a three foot long hole through stone or other masonry with the SDS Max hammer drill for running a 1" water line.

Your exhaust hole should be bigger than the intake hole. This ensures you don't create any back pressure in the cyclone.

Sent from my 831C using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.