Recommended Posts

Posted

Since purchasing my new(to me) 10" jet cabinet saw last fall I had not used my dado stack.  Over the weekend I needed to use it to build a wall cabinet. When I went to put the chippers on I had a heck of a time getting them on arbor.  I ended up having to spin one of the chippers onto the arbor just to get the thing on.

Has anyone else had this problem? Any suggestions on what I should do to fix it?

Thanks in advance for your insight.

Posted

I did with a Forest stack and a Grizzly saw.  I took the stack back to where I bought it and we measured the hole sizes of several different stacks until we found one that would fit my arbor correctly.  Yes, they were all a little different.

Posted

I had a Jet contractor saw that was tight with a couple of blades. I used a piece of emery cloth to take the slightest amount off the arbor. Just a few rotations did it.

  • Like 1
Posted
20 hours ago, drzaius said:

I had a Jet contractor saw that was tight with a couple of blades. I used a piece of emery cloth to take the slightest amount off the arbor. Just a few rotations did it.

You are saying take some off the arbor threads on the saw and not the hole on in blade? 

Posted

Because I had a couple of blades that I couldn't get on & the others were quite tight, I took some off the arbor. & threads. I glued some emery cloth to a piece of wood & held it to the arbor while it was rotating. It took surprisingly little to get it down to where all the blades fit fine.

If all the blade fit except 1 tight one, I'd do as others suggest & just do the 1 blade hole.

Posted

Okay, My $100 Freud and $30 irwin both fit pretty tight but can be pushed/wiggled on.  the two outside blades of the dado set could be wiggled on, but that one chipper had to be spun on.  Maybe I will try a combination of both..

last minute wedding plans are making it real difficult to justify spending anytime in the shop.  something about a wedding in 2 months has my fiance' freaking out :P

Thanks for the ideas.

Posted
21 minutes ago, Brian Endres said:

Okay, My $100 Freud and $30 irwin both fit pretty tight but can be pushed/wiggled on.  the two outside blades of the dado set could be wiggled on, but that one chipper had to be spun on.  Maybe I will try a combination of both..

last minute wedding plans are making it real difficult to justify spending anytime in the shop.  something about a wedding in 2 months has my fiance' freaking out :P

Thanks for the ideas.

Your priorities are clearly wrong. You should be getting those blades to fit ASAP :) 

  • Like 1
Posted

The Dewalt dado stack I have is tighter than I like it.  The Forrest stack goes right on the same saw.  I cursed the Dewalt when I was installing it the first time, but when I saw how perfectly cleanly it cut the bottom of the dado, I decided it was okay to be that tight.

Posted
20 hours ago, TIODS said:

It's a good idea to actually measure the arbor hole in the store before you buy. 

unfortunately I owned the dado stack before I purchased the saw. however the next blade that I purchase will be measured in the store.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 64 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined