Recommended Posts

Posted

A busy couple of days moving tools, running electrical lines, setting tools up etc. and Im looking forward to not moving or purchasing a large power tool for many years to come. My PM209 I purchased over a month ago arrived over the weekend. I purchased the straight knife model on sale(whoop-dee-doo 10%), but saved quite a bit by having the local shop put a byrd head in it for me. They brought it out early Saturday morning using the oddest hydraulic lift, and yes, that is snow on the ground in April. Getting the machine off the pallet wasn't too bad, and the built-in casters aren't terrible. Everyone complains about how craptastic they are, but the machine moves pretty well. It honestly took the better part of the day to wire a cord, plug, new 40amp line, and calibrate the machine. I get not supplying a plug(I was prepared with my own), but no cord is pretty lame. I had to run to lowes to pick up some rubber jacketed 8 gauge in the middle of setting it up. Overall, I haven't worked out all the kinks yet, but I imagine this will be a very impressive machine when I dial it in. The feeding is hit or miss at the moment. Sometimes I have pieces jam at the infeed roller. For whatever reason they hit that serrated roller and just stick. I either can shut the machine down at that point, or push like hell to get the board to go through the machine. Secondly, my gear box was leaking oil like crazy after first use. I was able to tighten everything up on the box, but it sucks that I had oil get all over the machine and floor. It wasn't a ton, but the resulting puddle makes me wonder if I need to top off the oil in the box. Something I would expect from Grizzly and not PM.

 

any suggestions on properly tuning all the parts of a planer for perfection? I only plane jointed lumber, so I set the bed rollers to .001" using my oneway gauge. My infeed and outfeed rollers are set to .02" per the manual, but it doesn't give you much to go on as far as adjusting spring tension. The touchy feeding makes me think I need to wax the tables again or my tension isn't strong enough. The infeed rollers aren't leaving much of an impression in the unplaned wood.

IMG_2278.JPG

IMG_2286.JPG

Posted

The gear box shouldn't leak. That's probably due to the head change. As for feeding, check the rollers on the bed. I don't really plane anything rough, so I turned mine so they barely protrude. Also make sure when you plane something you lock the bed in place with the knobs to minimize snipe.

Sent from my 831C using Tapatalk

Posted

Now for Round 2. While considering the PM purchase, I was concurrently on the hunt for a new band saw. Was a second away from buying a used MM16 before finding a used laguna LT20 in Florida. The owner passed away and his family was selling off his tools. The grandson agreed to crate the machine, and we agreed on a price. Shipping was incredibly reasonable, I thought, and it arrived yesterday evening. Right out of the gate, I had an "uh oh" moment, when I realized I never considered the height of my deck. The friggin saw is too tall to fit under it! I thought it was going to be pretty easy to use the mobile base to wheel the thing into the garage and tackle the doorway this weekend with a team. I ended up tilting the saw at an angle and carrying it on my shoulder like Jesus carrying the cross. This got the saw low enough to get to the garage, but I unlike Jesus, I wasn't man enough to handle the load. The 25-30' journey to the garage and wrestling it over the garage lip did me in. I allowed myself to be put in a compromised position to where I was losing grip, tired, and about to drop the top of the saw from waist height. Thankfully, my fiancé was able to lend a hand and we gently placed it on my foot. That could have ended with the machine getting damaged or somebody getting hurt. Now we had this big saw on its spine in the garage. Using a few levers, we picked the saw up enough to engage the mobile base and have the top on a furniture dolly. Big surprise there, the damn 1,000lb dolly from lowes explodes. This is the 2nd or 3rd one of these ive broken on moving tools. I substituted the hydraulic cart from harbor freight with a few more levers and we were in business. Pushed the thing home through the door, and Bob's your uncle. Now, I am tasked with getting this 83-85" saw upright in a basement with 86" bottom of joists. I feel like I need to line it up to tilt up parallel to the open joists prior to tilting. Some surface rust from being in florida, but I was very happy to see no pitting or anything else to worry about. As long as it turns on this weekend when I wire it, it will be a great remote buy. Somehow I paid $2000 and had to move the thing into my house myself, can you believe that? A poor deal on the Tom Scale.

IMG_2305.JPG

IMG_2307.JPG

IMG_2308.JPG

10 minutes ago, Brendon_t said:

Nice machine.  I didn't know it need a 40amp line.  That's quite a bit of juice dedicated. 

I tossed and turned on this decision. My sub panel had one open slot in it and that was supposed to go to the new bandsaw. I originally wanted the planer to share the 30amp line with the drum sander its right next to, but the PM manual states 40amp for the machine. One, I didn't want to somehow void my warranty if something went wrong. Two, upon rethinking it, I didn't want to unplug and replug two machines that I frequently use. I rearranged some lines, so I could run the 40amp line for the planer and the 30amp line for the bandsaw. The jointer and unisaw are 3hp, so they can share a duplex 20amp line. Everything should be at peace in the world now. Consensus seems to be that people run these on 30amp lines without problems.  

  • Like 1
Posted

Lifting between the joists seems like the ticket. 

Definately a poor deal on the TC scale but a nice one for us mortals. 

If it was tom,  he would have had it delivered on a hovercraft then set in place with magnitos power while a union electrical team powered it up and the deck was scrubbed.

  • Like 2
Posted

And, she's upright! Was pretty easy with the hydraulic cart and two guys except for my dad losing his mind and shoving the top off the cart while we positioned it horizontally on the ground. He had one job, keep it on the cart while I rotated the bottom end around, and he literally pushed it off the cart, so the thing fell 6" onto its spine. Thankfully it fell onto its spine and stuck there. No damage that I can see, but it could have been much worse if it rotated after falling. Took a few minutes to lift it back onto the cart, braced the bottom with a 2x4 against the opposite wall, jacked the top up to waist height and lifted it up tween the joists. 

 

Pens are on, I will run an outlet during intermission. 

image.jpeg

Posted

Grats on the saw, that's a big boy! I had to push my garage door up higher and put a clamp on the real to get the Mm20 in my garage. Crazy thing is since I lifted the door so high I unraveled the wire from the pulley and had to manually wrap it by hand while holding the garage door up with my shoulder.

Sent from my 831C using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 64 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined