Question for Tormek users and anyone who sharpens stuff.


Recommended Posts

Posted

I'm looking at getting one for my school workshop to  stop taking chisels, planes and other cutting tools to a sharpening service. I think we would end up saving money after a year or two. As well as having an easy option to accurately sharpen things when we need to rather than relying on the sharpening service.  

Posted

Great for touching up or sharpening a well shaped tool with a bit of wear.  Painfully slow for me when sharpening a flat tool. Nice for gouges and non-flat tools but, I have other ways of quickly putting an edge on flat stuff.  Repairing a chip or reshaping a bevel is another tool's job so I disagree that one could get by with a wet-grinder only.

Posted
3 minutes ago, gee-dub said:

Great for touching up or sharpening a well shaped tool with a bit of wear.  Painfully slow for me when sharpening a flat tool. Nice for gouges and non-flat tools but, I have other ways of quickly putting an edge on flat stuff.  Repairing a chip or reshaping a bevel is another tool's job so I disagree that one could get by with a wet-grinder only.

Hmmm. I've never been great with a bench grinder. I always burn the tip and ruin the angle. Time to start practicing a bit more. 

Posted

I use the Tormek for primary sharpening and touching up during a job.  I still go to my stones when I want something super sharp.  

Sounds to me like if you're paying someone else to sharpen for you, this would be a great option to save money in the long run.  Pick up some nice Shapton water stones to go with it and have a complete station!

  • Like 1
Posted

I have a tormek and like it.You really just don't know all the things you can do with one till you have it.

Plane blades will be hollow ground and then it's easy to balance them on a stone free hand.

Now you can get the same thing done on a dry grinder.But it's like sticking a pencil in a electric pencil sharpener.Your blades will get short pretty quick.

 

Aj

  • Like 1
Posted

Neighbor has a tormek and i just tried it today on a chisel i abused. It was a $1 box store special. I don't know if I'd like the tormek for plane blades or strait chisels. I feel like with a simple jig and water stones i can sharper faster and better. Now if you sharpen a lot of odd stuff and turning tools it might be worth it. The tormek was really slow compared to my water stones.

Posted
2 hours ago, Chestnut said:

Neighbor has a tormek and i just tried it today on a chisel i abused. It was a $1 box store special. I don't know if I'd like the tormek for plane blades or strait chisels. I feel like with a simple jig and water stones i can sharper faster and better. Now if you sharpen a lot of odd stuff and turning tools it might be worth it. The tormek was really slow compared to my water stones.

Was it just the speed you weren't happy with? I'm more interested in getting the perfect angles without burning through the edges rather than speed. Once the edge is established, it shouldn't take too much to maintain it. 

 

15 hours ago, TIODS said:

I use the Tormek for primary sharpening and touching up during a job.  I still go to my stones when I want something super sharp.  

Sounds to me like if you're paying someone else to sharpen for you, this would be a great option to save money in the long run.  Pick up some nice Shapton water stones to go with it and have a complete station!

If I go with the Tormek, I'll grab a few high grit stones to have a station setup that is easy to bring the tools and doesn't require packing away. I was just watching Marc's 60 seconds to sharp video. He mentioned he goes to 8000. Is there much difference going beyond this?

Posted
5 hours ago, lewisc said:

If I go with the Tormek, I'll grab a few high grit stones to have a station setup that is easy to bring the tools and doesn't require packing away. I was just watching Marc's 60 seconds to sharp video. He mentioned he goes to 8000. Is there much difference going beyond this?

I don't personally see any reason to go beyond that.  There's another thread that's pretty much about the very thing.

 

8 hours ago, Chestnut said:

Neighbor has a tormek and i just tried it today on a chisel i abused. It was a $1 box store special. I don't know if I'd like the tormek for plane blades or strait chisels. I feel like with a simple jig and water stones i can sharper faster and better. Now if you sharpen a lot of odd stuff and turning tools it might be worth it. The tormek was really slow compared to my water stones.

If that Tormek was slow and you can "sharpen faster" with your stones then you had to be doing something wrong.  I would agree if you were just touching up a chisel but, not an "abused $1 box store special"  Frankly, that's where the Tormek really shines! 

  • Like 1
Posted
5 hours ago, lewisc said:

Was it just the speed you weren't happy with? I'm more interested in getting the perfect angles without burning through the edges rather than speed. Once the edge is established, it shouldn't take too much to maintain it.

He didn't have any of the jigs that are good for woodworking tools so i can only comment on that it took a long time to regrind the bevel. You should ignore my comment from my minimal experience, see below.

 

1 minute ago, TIODS said:

If that Tormek was slow and you can "sharpen faster" with your stones then you had to be doing something wrong.  I would agree if you were just touching up a chisel but, not an "abused $1 box store special"  Frankly, that's where the Tormek really shines! 

It must have just been set up then. I know that he had a 1000 grit stone on there. Is there a more aggressive option? I can defiantly see how the tool is useful, i just think a guide and stones is a bit faster for single bevel tools.

Posted
1 minute ago, Chestnut said:

He didn't have any of the jigs that are good for woodworking tools so i can only comment on that it took a long time to regrind the bevel.

 

If he didn't have the jig for it then, I can see where it would take some time. ;)

2 minutes ago, Chestnut said:

It must have just been set up then. I know that he had a 1000 grit stone on there. Is there a more aggressive option? I can defiantly see how the tool is useful, i just think a guide and stones is a bit faster for single bevel tools.

That wheel is fine, the jig makes all the difference.  When set up properly, I can change a bevel on that wheel much faster than I can on a stone.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 63 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined