bushwacked Posted December 4, 2016 Report Posted December 4, 2016 So I'm just planning ahead on a build I'll need to do sometime to help make routing easier. I found this ... I don't want to spend $140 but I like the mobility of it which I need so I can store it when not in use. Questions... 1. What type of fence backing should I look into so I can slide the front panels back and forth to make the opening bigger / smaller. So type of t track fence? 2. I want a door on it to help reduce some noise but would I need more than the 1 hole in the door like they have for airflow? Quote
Brendon_t Posted December 4, 2016 Report Posted December 4, 2016 I believe the mdf fans on that will already slide back and forth by loosening those bolts. Are you restricted to a bench top table? I started with one and loathed it. super unstable, the top was aluminum and would warp plus it vibrated like crazy. Quote
RichardA Posted December 4, 2016 Report Posted December 4, 2016 Bush... You'd be better off making a top. All you need is some MDF and some t-tracks. Check out "Orange aluminum" for the tracks. You have a router, so making the grove for it is not a problem. Making the fence you need can be easily made with the same tracks to your spec's. Quote
bushwacked Posted December 4, 2016 Author Report Posted December 4, 2016 I believe the mdf fans on that will already slide back and forth by loosening those bolts. Are you restricted to a bench top table? I started with one and loathed it. super unstable, the top was aluminum and would warp plus it vibrated like crazy. Ya I guess they do. Maybe I confused people. I want to build a router stand like this. Not buy this. I am not restricted but it would be nice if the router did not take up additional space like it would if it had its own stand alone setup. Maybe a tablesaw setup but not sure how much actual workable space around that if I have a longer'ish piece i need to work with. Bush... You'd be better off making a top. All you need is some MDF and some t-tracks. Check out "Orange aluminum" for the tracks. You have a router, so making the grove for it is not a problem. Making the fence you need can be easily made with the same tracks to your spec's. Yep I'm planning on making the top. Ok so MDF would be better than plywood for the top and fence? I will look into the orange aluminum and see if I find what I envisioned in my head haha. Quote
rodger. Posted December 4, 2016 Report Posted December 4, 2016 I bought a cast iron router wing for my table saw. It's heavy as heck, with no vibration. Can also use the entire ts as table if needed. ts fence Works as router table fence by clamping on a piece of mdf. Quote
Immortan D Posted December 4, 2016 Report Posted December 4, 2016 I also need to store my router table when not in use, so I made it out of MDF and used the folding base from a cheap home center work table to support it. 1 Quote
Immortan D Posted December 4, 2016 Report Posted December 4, 2016 This is how it looks when stored flat against a wall, behind my band saw: Quote
Woodenskye Posted December 4, 2016 Report Posted December 4, 2016 I would get something like the attached. I have the Keter version without the router and use it a lot. http://www.homedepot.com/p/Husky-1-8-ft-x-3-ft-Portable-Jobsite-Workbench-225047/205887786?cm_mmc=Shopping|THD|G|0|G-BASE-PLA-D25T-Tools|&gclid=CjwKEAiAmo_CBRC9qbGQssjqi28SJABYTgZxDVa3A8W4_ARwLHvgdDwH6zqaDgI9ufL48NWh0gxXuBoCp1Lw_wcB&gclsrc=aw.ds Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.