Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Domino 500 on 2"+ thick stock

Featured Replies

Just finished the ottoman stools for the morris chair build(doing one in A. mahogany and one in walnut), and im about to start on the main chairs this weekend and next week while im off. This is the first time using the DF500 on true MT applications instead of panel alignment. It made pretty fast work of the ottoman joinery. I want to use it on the chairs, but the legs are not 2" like the ottomans; they are 2 7/8"-3". What is the best method for lining up my mortises on the 8 legs? Do I use some sort of spacer block under the DF500 to center the mortise? the 10x50 dominoes in tandem should be plenty strong for the front and bottom side aprons, but the height gauge on the 500 maxes out at 30mm.

 

See, i knew i should have bought the XL. I think if i did it all over again, i would purchase the XL package on craigslist for $800 instead of the 500 with cutters, accessories, and systainer with dominoes for $500. I guess now ill end up with both machines at some point.

 

Patrick

If you're worried about needing it to line up on center,  make a center mark and is the side notches of the tool to line it up there

  • Author
15 minutes ago, Mike. said:

You have a tablesaw right?  And a router?  

Time to do a real M&T.  

I do, and ive been down that road a couple times before, but it is sort of like driving through Ohio--boring af. That is kind of the whole point of the domino in my opinion, it cuts down on the lame repetition of woodworking. 

 

My thought was to use a 26.5(just call it an inch thick and be done) spacer board under the df500. Leg thickness is 73mm, i want the domino centered at 36.5mm, and i believe the mortise is centered 10mm above the base plate. 36.5mm-10mm=1" spacer under the 500 base plate?

1 hour ago, Pwk5017 said:

See, i knew i should have bought the XL. I think if i did it all over again, i would purchase the XL package on craigslist for $800 instead of the 500 with cutters, accessories, and systainer with dominoes for $500. I guess now ill end up with both machines at some point.

You bought the DF 500 set and the Domino assortment kit for $500 used off CL?! For those prices Id just have both the DF 700 and 500.

  • Popular Post

Anywhere I can clamp , screw or tack a straightedge I have cut a mortice. I learned this with my biscut joiner in the 80's. All you need is a reference line for the base of the machine. So your spacer block is just a portable device to define the reference line. Check your block with a pair of calipers, any variance in thickness will affect the location of your mortice. Same with the fence on the domino. My fence has slipped on one side a millimeter or so. You can lock the fence a bit higher than the height gauge, just check that both sides are equal. My Domino is one of the older models so your machine may be different.

I would make the block and practice on some scrap before I tackled cutting on the actual project.

You aren't limited to the depth of your fence, like Steve said, just attach a secondary "fence" in whatever manner you can come up with.

It's not a good picture, but I made this entire cabinet case, including the cubbies, with the 500.  I used a clamp on edge guide as a fence.

IMAG0029.jpg

Are you planning a single, centered domino?  You don't actually need to center the domino, so the spacer does not need to be exact, just close.  Also, how thick are the rails you are connecting to the legs?  Could you use two dominos for each joint and use the fence from each side?

  • Author

Planning two 10s next to each other. I've read it's a bad idea to reference from two different sides, because there is zero vertical slop in the mortise. 

 

I think im going to roll with my spacer board. If I'm following what you two are saying with a fence, that will involve lining up the straight edge against marks? I want it as consistent and dummy proof as possible over all 8 legs. And yes, Barron, you are right it doesn't have to be dead centered. Would people even recognize an offset of 6.5mm? Probably not. The rails and apron are 1" thick. 

47 minutes ago, Pwk5017 said:

Planning two 10s next to each other. I've read it's a bad idea to reference from two different sides, because there is zero vertical slop in the mortise. 

I'd guess whoever wrote what you read was lazy or laid out their lines with a piece of chalk. With a normal pencil or pen, there is no reason that wouldn't work. Clean layout lines,  careful tool placement would give a great joint and would be way faster than clamping and squaring an edge guide after figuring out your layout position.

I have not had a problem plunging from both sides. It's probably important that the faces to be joined are both square, and as noted above use a fine pencil to mark out your lines. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.