Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Advise on Dust Collection

Featured Replies

I have a 2hp 1200 CFM set up with 4" hose and a separator 1 micron bag,  1 line to miter saw,  and 1 line to table saw both of which are less than 8 feet, a third line going to band saw however it is shared with jointer and surface planer and oscillating belt sander these 4 tools are tool to tool no longer than 12 feet. I also made a sliding manifold instead of wyes as it will only be used by me so I just slide it to the tool needed. Is there something I should do different aside from getting a canister filter

11_4.jpg

la1.jpg

20170228_122558%20-%20Copy.jpg

20170228_134929.jpg

thanks for any input...

That machine can easily pull dust with 4" ducting from a tool that is 20' (equivalent duct length) away if the path is open only to that tool.  The main thing at I see with your set up is that your ducting is all flex hose.  The air resistance in one foot of flex is equal to about 3 feet of smooth pipe.

Question: where did you get the hose? Rona & homedepot has nothing but really stiff dryer ducting...(in canada at least, the states always seems to have more options)

54 minutes ago, Chelsea Tully said:

Thanks! I love lee valley, but generally avoid it, because it's $$!

I'll have to argue with you a little on this. For common stuff that is available anywhere, they're competitive. If you want the more specific, high quality stuff, of course you'll pay more. You get what you pay for.

I always comparison shop online, but if Lee Valley has it, that's usually my default. Sometimes they are a little more, but it's worth it to me for the service & convenience (they're 5 min away).

fair enough! yes they are very helpful.  total newb question... is it unsafe to use aluminum piping for dust collection?   it seems to be conducting electricity.  like small static zaps when you touch the duct.  like when your laundry is static... 

it scares me.  so I'm not going to use it till I do some more research.  might be another trip back to the hardware store.  

Aluminum is safe, but it's soft & easy to crush. I don't see it much except in home centers for dryer venting. Galvanized steel is much more common & works well. Buy you want to use at least 26 or 28 gauge. 30 gauge can get sucked flat if you leave a gate closed. I used 26 gauge spiral duct & it's the bee's knees.

Lots of people use PVC cause it's cheap, available & easy to work with. If you have very low humidity you might get the occasional zap.

2 hours ago, Chelsea Tully said:

I'm not going to use it till I do some more research.

There's a rabbit hole. Set aside lots of time that.

4 hours ago, Chelsea Tully said:

Thanks! I love lee valley, but generally avoid it, because it's $$!

Try busybeetools as well.

i have pvc and it works fine for me, use the thin wall septic version, i think its called schedule 30.

  • Author

well the change over has begun, based on the advice from Ronn W I am switching out as much flex hose as possible not finished yet but getting there..... cheers......

20170308_175731.jpg

  • Author

now down to only 4 feet or less of flex hose for the entire set up all smooth pipe ...sliding manifold is done including naming the ports so I don't forget....lol

1_39.jpg

On 3/2/2017 at 3:53 PM, drzaius said:

Aluminum is safe, but it's soft & easy to crush. I don't see it much except in home centers for dryer venting. Galvanized steel is much more common & works well. Buy you want to use at least 26 or 28 gauge. 30 gauge can get sucked flat if you leave a gate closed. I used 26 gauge spiral duct & it's the bee's knees.

Lots of people use PVC cause it's cheap, available & easy to work with. If you have very low humidity you might get the occasional zap.

There's a rabbit hole. Set aside lots of time that.

I have read lots of folks saying that 30 gauge galvanized steel is susceptible to collapsing if no gates are left open but I just got done building mine and tested this and had no issues. I have it hooked up to a Jet 3hp cyclone and am running 6" mains and reducing to 4" at the tool. All of my joints are sealed with metal tape so I know it is airtight as well.

Not saying that it isn't possible but my experience is that 30 gauge works fine without the risk of collapse.

54 minutes ago, TheWoodYoda said:

I have read lots of folks saying that 30 gauge galvanized steel is susceptible to collapsing if no gates are left open but I just got done building mine and tested this and had no issues. I have it hooked up to a Jet 3hp cyclone and am running 6" mains and reducing to 4" at the tool. All of my joints are sealed with metal tape so I know it is airtight as well.

Not saying that it isn't possible but my experience is that 30 gauge works fine without the risk of collapse.

If you put in a blower with reverse curved vanes (Clearvue or Oneida), it will pull a higher vacuum & quite possibly collapse the 30 gauge duct.

  • Author

might as well go 4" and 5" muffler pipe and get them to bend it the way you need it....

17 hours ago, drzaius said:

If you put in a blower with reverse curved vanes (Clearvue or Oneida), it will pull a higher vacuum & quite possibly collapse the 30 gauge duct.

I'm going to show my ignorance and ask what you mean by how reverse curved vanes create higher vacuum. I'll admit that I am a novice when it comes to setting up DC. I just tried something out for mine based on research I had done and it happened to work with no issues. 

An impeller with forward curved vanes, that is, the vanes curve forward into the direction of rotation, will produce very high CFM. But that volume will fall off sharply with an increase in pressure. These are not suitable for a dust collection system.

Straight vanes; lower CFM but higher pressure. This will work for dust collection, but performance falls off badly with duct restrictions & filter cake.

Reverse curved vanes: lower CFM but much higher pressure capability. This will cope better with duct restrictions, cyclones & flow will fall off less as the filter fills with cake.

I'm not saying that all 30 gauge duct will collapse, but if you have a good, powerful blower, the chances of collapsing the duct are pretty high if you leave all the gates closed. The larger the duct, the more danger of collapse. 

Spiral duct is stiffer for a given gauge & I've see a video where the guy put circular braces around the duct every couple of feet or so to keep it from collapsing.

23 minutes ago, TheWoodYoda said:

I'm going to show my ignorance and ask what you mean by how reverse curved vanes create higher vacuum. I'll admit that I am a novice when it comes to setting up DC. I just tried something out for mine based on research I had done and it happened to work with no issues. 

 

  • Author

before I got the 55 gallon plastic drum, very study and solid for all accounts I purchased what I thought was a tough enough garbage can. a very rigid plastic can I connected everything up and sealed everything around the can...good to go.......I thought!

I turn on dust collector and bingo flattened the can is seconds....useless.....I even put wood strips on the outside of the can to help it but still no go.....

my blower happens to have reverse fin is that uncommon for dust collectors?

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.