LazarusDB Posted March 4, 2017 Report Posted March 4, 2017 We've been in our house for almost three years now and finally getting around to building a new bathroom vanity. The current vanities are original to the house (about 30 years old) and must have been made for extremely short people as they are only 30" tall. Even for my wife who is only 5', that's a short vanity. First step was to pick up the birch plywood and poplar. I no longer have a truck so I usually buy these 2' x 4' precut sheets. I cut the carcass pieces to size and then cut a dado for the bottom shelf to rest in and started assembly. I used pocket holes for the other support pieces for the carcass. I won't be putting a solid back on. Carcass is now assembled and squared up. Now on to the face frame. Quote
wdwerker Posted March 4, 2017 Report Posted March 4, 2017 Going with a solid wood faceframe ? If I use edgebanding I put it on first and trim it before I assemble the case. Looks better than the vanities you could buy these days. Quote
LazarusDB Posted March 4, 2017 Author Report Posted March 4, 2017 13 minutes ago, wdwerker said: Going with a solid wood faceframe ? If I use edgebanding I put it on first and trim it before I assemble the case. Looks better than the vanities you could buy these days. Yes, going to use poplar for the face frame, drawers and drawer fronts. Probably for door frames as well. Designing as I build. Quote
Popular Post LazarusDB Posted March 4, 2017 Author Popular Post Report Posted March 4, 2017 Face frame is done. Hopefully get to the doors and drawers tomorrow. Aaron 6 Quote
LazarusDB Posted March 12, 2017 Author Report Posted March 12, 2017 Was away on a business trip this week but finally got some more work done this weekend. I cut the drawer pieces, used the miter lock for the corners and 1/4" dado for bottom plywood. I used a bottom mount, single rail for the drawer glides. Not the best quality but works nicely. I then installed tilt out trays as the top drawer. These trays are usually used in kitchen sink cabinets but thought it would make a good place for tooth brushes, hair brushes, etc. Next up will be drawer fronts and doors. Aaron 2 Quote
Popular Post LazarusDB Posted March 19, 2017 Author Popular Post Report Posted March 19, 2017 Next up was to make the doors. I was going to go the easy route and use pocket screws but decided to do mortise and tenon instead. Now to mount the doors. I made a mistake when cutting the mortises but it allowed me to use the mistake piece to test the hinge placement. I used slow close, 1/2" overlay concealed hinges. I then used a solid piece of poplar for the drawer fronts. Next up will be a couple coats of wipe on poly for the interier and paint for the exterior once my wife decides on a color. Aaron 4 Quote
Chet Posted March 19, 2017 Report Posted March 19, 2017 Nice work Aaron. That should look good when you get it in to the bathroom. Quote
wdwerker Posted March 20, 2017 Report Posted March 20, 2017 Lookin good ! , Even if it is green. In the meanwhile you can prime and sand while the color choice is made. Keeping the door flat during glueup is important, I use cauls to keep clamp pressure from bowing the joint. Quote
prov163 Posted March 20, 2017 Report Posted March 20, 2017 Coming along quite nicely. Looking forward to seeing the finished product installed. Quote
wtnhighlander Posted March 20, 2017 Report Posted March 20, 2017 Very nice, Aaron. Don't forget to peel the barcode off the plywood before you paint! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.