Recommended Posts

Posted

Set up to do a little sanding today. Had it setup like this. Didn't check which port on the vacuum I had the hose connected to. Who wants to take a guess!?!883e6031e98011668dcb64c61dc1e796.jpg

 

Sent from my SM-G930T using Tapatalk

 

 

  • Like 1
Posted

 

Set up to do a little sanding today. Had it setup like this. Didn't check which port on the vacuum I had the hose connected to. Who wants to take a guess!?!883e6031e98011668dcb64c61dc1e796.jpg

Sent from my SM-G930T using Tapatalk

 

I am guessing it turned out to be a dust confetti cannon. I haven't done that yet, but I have started planning without the DC connected and I would guess that it was a similar result. . .

 

  • Like 1
Posted
 

 

 

 

I am guessing it turned out to be a dust confetti cannon. I haven't done that yet, but I have started planning without the DC connected and I would guess that it was a similar result. . .

 

All over the place. Here soon all the air stuff will be in a cart. Until that point I need to pay more attention and have more caffeine. At least I wasn't streaming at the time. My viewers would of never let me hear the end of it.

 

Sent from my SM-G930T using Tapatalk

 

 

Posted
All over the place. Here soon all the air stuff will be in a cart. Until that point I need to pay more attention and have more caffeine. At least I wasn't streaming at the time. My viewers would of never let me hear the end of it.

 

Sent from my SM-G930T using Tapatalk

 

 

 

Always good to keep our embarrassing moments private... oh wait you posted it on the internet. I haven't been at this woodworking thing long and man... I feel I have had all the embarrassing moments a 30 year woodworker experiences.

  • Like 1
Posted
 

Always good to keep our embarrassing moments private... oh wait you posted it on the internet. I haven't been at this woodworking thing long and man... I feel I have had all the embarrassing moments a 30 year woodworker experiences.

I tend to laugh at my moments. Helps me learn from it. Well. I might learn one year.

 

Sent from my SM-G930T using Tapatalk

 

 

Posted

Don't worry there are still plenty of embarrassing moments at 40 years ! You just have to learn from it and move on . I would have loved to have seen the cloud of dust ! We could all use a good laugh .

I try to admit to my mistakes in my posts so everyone might learn and avoid them .

  • Like 1
Posted
Don't worry there are still plenty of embarrassing moments at 40 years ! You just have to learn from it and move on . I would have loved to have seen the cloud of dust ! We could all use a good laugh .

I try to admit to my mistakes in my posts so everyone might learn and avoid them .

I'm really lucky there was a board leaning up behind it. Deflected most of it. And I'm sure I will make a few on stream for people to laugh at. I already spin in circles a lot looking for things. I look like a lost puppy dog or something.

 

Sent from my SM-G930T using Tapatalk

 

 

Posted

When I first got my track saw I was all pumped not to have to clean up after using. So I had the shop vac hooked up turned it on, turn the saw on and forgot to plug the hose all the way into the vac.  Man I felt stupid, and was like dust collection wasn't as advertised.

  • Like 1
Posted

Well, since I don't want to start a new thread, I'll claim this one as a generic oops thread.

Cutting down the lengths of stock to glue up with the veneer for the segmented bowl I'm doing.  Each Length was careful labeled, and the wide dimension of the piece was indicated (they are 7/8" x 3/4", easy to confuse).  Then I laid out all the veneer, stock, and HDPE strips (calls) on my clamps to do one bulk glue up.   Bam, done.   Get home this morning.   And I glued the veneer over my writing.   :blink:

Posted
Well, since I don't want to start a new thread, I'll claim this one as a generic oops thread.

Cutting down the lengths of stock to glue up with the veneer for the segmented bowl I'm doing.  Each Length was careful labeled, and the wide dimension of the piece was indicated (they are 7/8" x 3/4", easy to confuse).  Then I laid out all the veneer, stock, and HDPE strips (calls) on my clamps to do one bulk glue up.   Bam, done.   Get home this morning.   And I glued the veneer over my writing.   :blink:

Haha I love the idea of an oops thread. And ouch.

 

Sent from my SM-G930T using Tapatalk

 

 

The pallets revolted, and ate your vac?

Probably. They are getting impatient because it takes me 2 days to break one down.

 

Sent from my SM-G930T using Tapatalk

 

 

When I first got my track saw I was all pumped not to have to clean up after using. So I had the shop vac hooked up turned it on, turn the saw on and forgot to plug the hose all the way into the vac.  Man I felt stupid, and was like dust collection wasn't as advertised.

Did you contact the company to complain before you figured it out?

 

Sent from my SM-G930T using Tapatalk

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 41 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32k
    Total Topics
    437.5k
    Total Posts
  • Member Statistics

    26,007
    Total Members
    3,644
    Most Online
    FurniCore
    Newest Member
    FurniCore
    Joined