Recommended Posts

Posted

Late last year a friend asked if I could cut a sign for his son-in-law's new business.  I was more than happy to do that so he brought the piece of wood by the house and it's been sitting in the shop since then because there were quite a few projects ahead of it (the Curly Maple and Walnut cross being one of them).  So yesterday I put the Pecan slice up on the work table to begin mounting it on the CNC.

The piece of wood is from a Pecan tree that had to be cleared from the property before the building could start so this has a bit of sentimental value for them, maybe more nostalgic than sentimental, but either way I have one shot at this.  When we first talked he just wanted the name engraved into the Pecan slice.  The second time we talked they decided they wanted the logo as it is on the business card and for that to be raised from the surface.  Now, in concept anyway, I understand what needs to be done to accomplish that but I had never done it.

I worked through setting this up in Fusion 360 for what seemed like days - an hour here, two hours there, etc. - and never got comfortable with the generated toolpaths.  In the setup for cutting this was leveling the face with a 1.5” bottom clearing bit, about 6 minutes, and from there it got complicated and difficult.  In Fusion 360 when I set up the next bit, a 1/2” flat bottom bit, to begin cutting away everything except the logo and letters I never could get the geometry correct.  When I got it to a point where it was acceptable the cutting time was over 2 hours and I just didn’t think it should take that long. 

When I switched to a 1/4” bit to cut what the ½” bit couldn’t get to the time doubled – over 4 hours.  No matter how I set the parameters I couldn’t get it set to only cut what the 1/2” bit couldn’t get to even though I had “from previous operation” selected.  It wanted to cut the entire piece as though the 1/2” bit was never involved.  When I switched to a 1/8” bit the time was truly ridiculous!

I finally turned to the Fusion 360 community where I gave them my files and noted the issues I was having.  A gentleman there took the project, reworked my files, and sent his version of how the CAM portion should be set.  He did some things in the setup that I still don’t fully understand but they seem like they’re going to work.

So here are some photos and minor progress; this is the slice as delivered -
001%20-%20Pecan%20slice%20as%20received_

Logo and name from their web site -
002%20-%20Logo_zpsitqsalji.jpg

I used CorelDraw to overlay the proposed letters and logo for approval.  One thing I had to work around is the void in the center -
003%20-%20Coastal%20Urgent%20Care%20-%20

The initial toolpath for the 1/2" bit follows the approximate outline traced from the photo.  Turns out this isn't entirely accurate but at this point, since I didn't draw that outline (the guy from the Fusion 360 community added that and I can't seem to edit it), what this doesn't cut will be a tiny bit on the perimeter so I'll just finish this by hand when it comes off the CNC machine -
004%20-%20Initial%20toolpath%20with%20.5

Here's the toolpath for the 1/4" bit, cutting only what the 1/2" bit can't get to -
005%20-%20Toolpath%20with%20.25%20bit_zp

And ditto for the 1/8" bit, cutting what the 1/4" bit didn't -
005%20-%20Toolpath%20with%20.25%20bit_zp

One step that was necessary from the start is that I had to draw the logo.  I drew this in CorelDraw and exported it as an svg file to import into Fusion 360.  I had to keep modifying it because even a 1/8" bit wouldn't get to the entire logo.  As it is I'll finish the tiny openings near the bottom with a Dremel, 1/16" bit, and router base.  I can control that pretty easily but don't want to risk breaking my 1/16" bit for two little holes.

Fixing mounting boards to the bottom of the Pecan slice -
007%20-%20Mounting%20boards_zpsmaxjhjq9.

Verifying it is close to level so I wouldn't have to take much off for surfacing -
008%20-%20Verifying%20it%20is%20level_zp

You can see how large this is relative to the CNC.  The CNC frame is a [URL="https://www.finelineautomation.com/products/saturn-series-2-x-4-cnc-router?taxon_id=54"]Saturn 2' x 4' from Fine Line Automation [/URL]but the actual cutting area is 26" x 50".  The Pecan slice is 25 7/8" across at the widest point.  No problem, right?  Wrong!  When I did the surfacing profile in Fusion 360 I didn't count on the machine needing turn around room a the end of each pass.  The loops at the end of each pass pushed the X axis right into the bumpers and tripped the sensor.  So I moved the starting origin point for X about 1/2" to the left but it made no difference.  Fortunately the sensor stopped it before crashing into anything at 600 ipm.  I toyed with it for a while and finally had to go back into Fusion 360 and tell it the piece was only 24 3/4" wide and then it cleared by 1/8".  Since it was only the facing operation and I could see it was going well past the perimeter and it wasn't going to be a big deal, I would just change it back for the letters and logo. 
013%20-%20Initial%20facing%20toolpath_zp

Once I was comfortable with the clearance, having run it about an inch above the Pecan slice to make sure, I set zero, fired up the spindle, and hit go.  Two things became apparent right away - 1) even though I had the dust shoe on and DC going, tiny Pecan chips were going everywhere and, 2) the large flat bottom bit didn't like climb cutting at all.  It was burning on each pass that was climb cutting but clean on the conventional cutting.
010%20-%20Burning%20on%20climb%20cutting

Back to Fusion 360 to change the toolpath to only cut conventional (no loops at the end, rather it raised the Z axis and went back to the other side to cut in one direction only for each pass) -
014%20-%20Final%20facing%20toolpath_zps1

These tiny little Pecan chips were all the way to the window 15' away, down my shirt, in the keyboard, even under the CNC machine!
011%20-%20Pecan%20chips%20everywhere_zps

This came out much better and took a few passes but it cleaned up nicely.  You can see the lines along the X axis but it is very smooth.  It will all be cut away in the next step anyway -
012%20-%20Surfaced%20nicely_zpsubpg4fjw.

I think it's a pretty piece of wood and with a little sanding should look pretty nice.  I have two other jobs that need to be finished by Tuesday so I may pull this off and move on to those, then mount this again for the letters and logo.  At this point it won't matter if I take it off but once I start the letters and logo I can't move it, so instead of getting backed into a corner this will probably come off tonight.

More later -
David

  • Like 2
Posted

I thought with CNC you just put the wood down and hit start. < Sarcasm. 

Is your 1-½  it straight or upshear and what are your feeds, speeds and stepover percentage? Also, depth of cut per pass?

Posted

LOL!  I thought that too so I built one... ;)

It is a straight bit, 15k rpm max (I ran it at 12k), feed was 200 ipm, stepover was 1.25", depth of cut was 0.075", so all in all not very aggressive.

Posted

The operation you're doing is essentially a table mill. With a 1 1/2" bit I wouldn't step over more than about 40% of the tool width. That's probably where the burning came in. More than 50% and you're simultaneously climb and conventionally cutting.

  • Like 1
  • 3 weeks later...
Posted

David, I am not personally interested in using a CNC machine in my work, as I generally enjoy the process of doing things by hand. But for the rare occasions when I make a sign, I would use one in a heartbeat!

 

That one turned out great!

 

Are you doing anything else to the "cookie" to minimize cracking?

  • Like 1
Posted
15 hours ago, wtnhighlander said:

Are you doing anything else to the "cookie" to minimize cracking?

I'd like to know that answer as well. Heck of a job David. As a cnc non-believer, I'm gradually coming over;)

  • Like 1
Posted

Glad you like it - fun job!!

He's coming over tomorrow to pick it up and has said he'll finish it in a clear varnish or Poly,  I'll suggest to him that I can spray it with Nitrocellulose lacquer but he might be better off brushing on a few heavier coats of the varnish or Poly.

I have found the CNC to be a good tool for the shop and I use it when it makes sense.  I have some regular work I do for a trophy shop and there are several steps that could be done on the CNC but I can do them on the router table or table saw much quicker and just as accurately.  But there are other steps that I would spend 4-5 times as long to use any tool other than the CNC.  It's pretty rare when I do something on the CNC just because I can, it usually has to provide a benefit - accuracy, repeatability, engraving, CNC can work on one thing while I work on another (my digital employee - LOL!), etc.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 56 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined