Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Walnut color tone blending

Featured Replies

DSC_0048.thumb.jpg.c8b7b3e46b1f7d7535149018c57c4f69.jpg
I am in the process of completing a walnut midcentury nightstand piece.
The image provided shows the solid walnut legs, solid walnut drawer face to be attached, and one side off the walnut plywood case body with a  3/4” x  1/8” walnut edge applied.
None of these pieces are final sanded yet, no finish has been applied.
The legs and edge banding are the same walnut color tone.
The walnut plywood is another walnut color tone, a little lighter/grayer than the legs or banding.
The drawer face, which I cut to show the grain pattern has a little bit of red in the walnut color.
Question is…..
How to insure that the finished piece does not look like three types of wood? How do you bring all these color tones together?

I use a fair amount of walnut.  Like cherry the colors can run pretty wide.  The plywood is the rub.  If I were to do it again I would shop the yard for solid material to more closely match the ply.  With your solid material in the walnut 'red' spectrum and the ply in the more 'gray' spectrum you will have to move them closer together.

I prefer to avoid colorants but, have begun adding some dye to my walnut pieces that is not really perceptible.  The color is just there to combat the natural lightening that happens to walnut.  you can do the same but, with the intention of moving both colors toward a more brown appearance.  How is the veneer on your ply?  Is it pretty thick?  Paper thin veneer will allow the glue to telegraph when the finish hits it so test things out on some scrap (of course).

I use Transtint and they do offer a Dark Walnut and a Coffee Brown, both of which have bluish browns rather than reddish.  I would test with some dye added to an oil/varnish blend and see how you like it.  I sometimes have a dozen "swatches" on a length of board surface prep'd identically to my project.  Identical material and surface prep ios the only way to truly know what you are going to get.

Here's a glued-up top panel with a fair amount of difference (really shows on the left hand tongue).

5837ca4a93911_GnGLowCoD(191).jpg.266c7fc23fe44adbf258e0dcbf797d8a.jpg

And the end result.

58056868804de_GnGLowCoD(291).thumb.jpg.dd20fce322bd7357ef04fff606f2f8fd.jpg

 

it does look a little different but i think you may be over-thinking it, put some finish on the non-show sides and see how it looks, oh, and welcome to the forum and be sure to post some pictures of it done.

I spray most everything that isnt getting oil nowadays and having a cheap gun specifically for concentrates and dyes is really handy.

For my personal work I dont need nearly as much consistency as the work for my job.

So at work this is what I do when needing to shade in stuff-

-After sealing a piece you can get a good idea for what it needs and where - whether its black, brown, red, yellow, orange, etc.

- After figuring out what it needs (color wise) for everything to look the same, I will usually reach for a solvent concentrate and (on lighter colors where you can easily mess something up with too much dye) thin it down- usually 90% acetone 10% dye.

-set up for what im doing -

  • shading an entire panel evenly-  i will wind the fan all the way out and very little fluid, decent amount of air and just take my time,
  • spotting- smaller fan, very little pressure but enough to get good atomization
  • highlighting- usually slightly higher pressures, no fan, medium fluid and relatively far away from the piece.

most dies look very different when under some clear so whenever you put down some dye you will need to top coat it again.

 

 

you sort of can spray on non-sealed pieces but it is so difficult to get a good idea of what it will look like and get consistent results, i dont bother with it.

Dying them to match takes a fair amount of practice. Practice on scraps and backsides until you are comfortable. Don't just practice the dye, it looks much different after there is a coat or 2 of finish over it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.