Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

GF Gel Topcoat sanding?

Featured Replies

I am using General Finishes Gel Stain and Topcoat to work up a finish scedule for a small mahogany table.  My previous experience has been with the old Bartley gel products.  

The GF Topcoat instructions call for sanding with 320 between coats.  The old Bartley products did not call for sanding.

I am working up a test piece, applying the topcoat with a rag.  Old habits, I forgot to sand between the first two coats.  Before the 3rd coat I did a light dry sanding with 320.  

Not that thrilled with the result.  I thought it looked better with 2 unsanded coats than it does now with sanding and a 3rd coat.  It seems dull and maybe streaked.

Wondering if I should excercise my inalienable right to pursue the happiness of not sanding, or would that be commiting high crimes and misdemeanors?

Sand then raise the grain w water or water alcohol mix. Sand again, then gel stain & dry. 2 thin top coats then sand lightly before final coat. 

Polyurethane does not stick well to itself.  That is why most poly finish manufacturers recommend sanding in between coats.  It is not for better appearance (although it might help get a smoother finish).  They recommend sanding for better adhesion.  It creates some mechanical bond.  

Other varnishes (like phenolic such as Waterlox) don't need in between coat sanding because phenolic resin sticks better to itself.  

 

A scrub w a red or grey abrasive pad will lessen the chance of cutting through the first top coat then, sanding through the stain is difficult to touch up.

  • Author
1 hour ago, Mike. said:

 They recommend sanding for better adhesion.  It creates some mechanical bond.   

So the game plan is to scuff the surface rather than go for smoothing.

53 minutes ago, wdwerker said:

A scrub w a red or grey abrasive pad will lessen the chance of cutting through the first top coat then, sanding through the stain is difficult to touch up.

What abrasive pads are you referring to? Red? Grey?

Scotchbrite is one brand but several companies make them . Big box should have some.

Green= Xtra coarse

Red/maroon = coarse

grey = medium

white = super fine

Great for sanding between coats on tops and moldings.

1 hour ago, wdwerker said:

Scotchbrite is one brand but several companies make them . Big box should have some.

Green= Xtra coarse

Red/maroon = coarse

grey = medium

white = super fine

Great for sanding between coats on tops and moldings.

Lee Valley sells some as well.  I bought the white one at LV after Steve recommended it a while back.  Works great for rubbing out water based topcoats.

Gel Topcoat is the same as their gel stains only without pigment.  Have you considered using Armor Seal.(ARS).  Must admit that I have never used Topcoat as a final finish.  Let us know how it works out.

FWW did an article on applying gel topcoats a while back.  A search at their website will probably turn it up.

  • Author

I will check out FWW and see what I find.  I also need to pick up some of those Scotch Brite pads.

I am trying another test piece that's a little bigger so more room to work. I'll do one side sanded between coats and one side not.  And I will be more gentle on the sanding which I may do wet.  

Thing with test pieces is that they take about as long to do as the real thing.  You still have to wait X hours between coats.  

Obviously I am trying to get out of doing a step I don't want to do.  I have to keep reminding myself that more than one piece has been lost at the "Finish Line".

The gel topcoat really sits on the surface of the wood and not a huge film builder, plus you have to wipe it back, thus reducing film thickness even more. I always think of the gel topcoats for items not requiring a lot of protection, such as picture frame. 

By sanding between coats, due to the fact, the film is so thin, you're probably cutting down into your stain layer. I would consider sanding with a minimum of 3 coats down first and use 400 grit or better yet 600 grit sandpaper and use a wiping motion. In my opinion, the synthetic steel wools will ride over nibs or thick areas. Sandpapers will cut the finish smooth and level.

 

-Ace-    

  • Author

 

14 minutes ago, AceHoleInOne said:

.... I would consider sanding with a minimum of 3 coats down first and use 400 grit or better yet 600 grit sandpaper and use a wiping motion...

Would you sand wet (mineral spirits) or dry?

23 minutes ago, Mark J said:

 

Would you sand wet (mineral spirits) or dry?

Dry sand. The finish is ready to sand when it powders-up. If your paper is clogging, wait a few more days. 

 

-Ace-

 

  • Author

Well I finished another test piece.  Two color coats of the gel and three clear.  On one side I just scuffed the surface with the grey 3M scratchy pad between coats of clear.  On the other I didn't sand.

Like Mike said, not much difference in color or sheen, but noticeably smoother to touch (and the wife likes it better) so scuffing it is.  

I will try ARS eventually (it is very well regarded here).  I went with gel products because they are a known to me.  

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.