Recommended Posts

Posted

 I have a couple of routers that I have hardly used. I would like to learn how to do more with them and for now I have a very simple project that I'm having trouble with. I need to edge plane a few 16 ft boards to narrow them just  1/16 th or so. I'm thinking a bearing guided 1/16 "basically a rabbeting bit, then another pass with a bearing guided flush cut bit. For some reason people are looking at me like I have two heads. Am I missing something here? Is this not a good idea? I don't have a router table and working alone seems like 16 ft is too long to get a good edge even if I did. I'm thinking using the original edge is the easiest and simplest way to take just enough off the edge to get the new deck boards to fit the decking. This is for replacement deck boards BTW. The new one are either slightly wider than the originals (too little difference to measure with a tape or ruler, or swelling with time and the moisture may be causing this problem.. I'm thinking a 3/8 flush cut bit with a 5/16 bearing diameter would make my first cut but can't seem to find anything like this. Am I looking for "Hen's Teeth"? Can anyone recommend a source?

 

Posted

Your idea with using the smaller bearing on a flush cut will work as you said it's just not the normal way most would do it is why you are getting the strange looks. But you can buy router bearing kits with multiple sizes in it I know woodcraft an several other woodworking site carry them

Posted

Yea I always get a kick out of them trying to help me. You can always go online an order it if you have a few days you can wait. Or the trusty table saw or hand plane as a option last resort belt sander lol

Posted
13 hours ago, PanelDeland said:

I'm thinking a bearing guided 1/16 "basically a rabbeting bit, then another pass with a bearing guided flush cut bit. For some reason people are looking at me like I have two heads. Am I missing something here? Is this not a good idea?

I absolutely do this.  I have a stepped set of bearings and various other bearings that I have collected along the way for the sole purpose of making router bits do more.  I have used the technique you mention to enlarge holes, dimension frames and other odd tasks as a fix for something that has made it too far along to be done with more common methods.  The common method for what you are doing would be the tablesaw.  If you only have a lightweight tablesaw I can see bringing the tool to the work.

Bearings-stepped.jpg.cc347e06d55562937916e2eb7cd65f84.jpg

594e716a33454_routerbitbearings(1).jpg.7fdff840aeee3a35db52f9f670ed8265.jpg

As to a source for a bearing to fit your bit that is 1-16" smaller in diameter, the manufacturer would be a good source if this is a one time deal.  If you have not bought the bit yet, they even make sets for this purpose.  Let me look . . . Darn it, not finding it.  If I do I will post back.

Be that as it may, bearing "kits" are premium priced at places like Rockler and Woodcraft but, depending on your need and schedule, the premium may not be out of line.  Again, if you are ordering the bit, just order a Whiteside and the extra bearing you need.  That way you will be sure of the fit.

In their quest to be all things to all customers, the budget bit folks sometimes use bearings that are 'almost' the right size.  This may function long enough to get through some rough work but, for precision and long life, something spinning that fast really ought to fit right :)

 

P.s. Hartville has good prices on Whiteside and ships free.  Holbren also handles Whiteside and has outstanding customer service.

Posted

@PanelDeland, I am currently re-flooring my deck. Beware that most decking material is not completely dry, and will shrink over time. Don't take too much off, it other words.

 

An option would be to clamp a straight edge under the board, with the 1/16" offset, and run the bearing of a standard flush trim bit against that.

Posted

I'm assuming "edge plane" means "joint"...i.e - you want to make a bowed board straight.  Which is what jointers are for.  You can joint an edge with a router and a straight edge but if you just follow the existing edge of the board with a pattern bit, you'll just get a skinnier board with the same bow...and at that point you might as well just use a table saw...because neither will make it straight.

Or are you just trying to make a wide board skinnier?  Again...table saw.

I guess I'm confused by the question.

Posted

In theory, your idea will work, if you are only trying to take a 1/16 off the width of the board.  I do the same technique to make wider holes. 

But as other people have mentioned, there may be easier ways to do it, and other concerns about making deck boards smaller, along with Eric's comment about bow. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   4 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined