Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Breadboard question

Featured Replies

How do I get it to where the breadboard isn't going to expand past my perpendicular panel? Is there a good, efficient way to minimize it? 

8/4 walnut, biscuited panel, planning to t&g the bb into place and then sticking a few dowels through as well. What's the best practice? Am I on the right track? 

Lose the biscuits and use several spaced out tenons on the panel which will mate with mortises in the breadboard.  Glue the center tenon and pin the outer tenons with drawbore pins.  (You pin all the tenons but only the center is glued.)

The breadboards won't expand and contract very much, the panel will.  Depending on what time of year it is, the panel will be either slightly proud or slightly recessed of the ends of the breadboards.  This is perfectly normal and acceptable.

The breadboard won't change length, it's your top that expands and contracts. If you put the breadboard on flush when the top boards are at the lowest moisture content then the top might expand to wider than the breadboard. If you assemble the top when the moisture content is high the top may eventually shrink and the breadboards would protrude.

Plain sawn boards will move the most across their width, rift or quartersawn boards move much less. The length of hardwood changes so little it's not worth worrying about, so the breadboard won't change length.

  • Author

Lose the biscuits and use several spaced out tenons on the panel which will mate with mortises in the breadboard.

 

Biscuits are running down the length of the panel aligning my entire top. I plan to mortise or t&g the breadboard to the center panel..

 

You're talking about the breadboard, right? You just thought I meant biscuiting the breadboard on?

 

 

 

Sent from my iPhone using Tapatalk

14 minutes ago, Kyle Farmer said:

You just thought I meant biscuiting the breadboard on?

Correct.  Disregard the biscuit comment.

T&G to attach the breadboard doesn't seem like a good idea to me unless it's a narrow breadboard or a looong tongue into a deep groove.  If you do it this way, you can't glue the whole joint either. 

9 minutes ago, bleedinblue said:

If you do it this way, you can't glue the whole joint either. 

This is the only way I do bb ends. Long t/g keeps the outside flat without glue, center few inches glued keeps it secured.

Just now, Brendon_t said:

This is the only way I do bb ends. Long t/g keeps the outside flat without glue, center few inches glued keeps it secured.

How long do you make the tongues in relation to the BB?  Half?  I can just imagine a lot making a half inch tongue and groove into a 5" BB, and probably those same people gluing the whole joint. 

8 minutes ago, bleedinblue said:

How long do you make the tongues in relation to the BB?  Half?  I can just imagine a lot making a half inch tongue and groove into a 5" BB, and probably those same people gluing the whole joint. 

I don't have a hard and fast rule. This is a common sense thing for me. Breadboards on a 1/2" thick jewelry box lidmostly there for looks can easily get by with a half inch tongue. A 5”  of 8/4 obviously needs some more meat behind it.. 

For a 5” bb I would probably go 2" or close to it.

I agree.  I wasn't really looking for a direct number or ratio, just making a point. 

The reason that a long T&G is inferior to several tenons is because the T&G removes so much material in the breadboard that it can compromise its strength and therefore defeat its entire purpose.  Using tenons leaves considerably more material in the breadboard so it can sufficiently do its job which is resisting cup in the panel.  Traditionally you have a narrow tongue that runs the entire width of the panel, but the majority of the male part of the joint is cut into three or more tenons, rather than leaving only a single, wide tongue.  Depending on the size and thickness of the panel and breadboards, this may or may not be necessary in reality...but it's technically the correct way to do it.

 

nD6MibU.png

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.