Woodworking_Hobby Posted February 14, 2025 Report Posted February 14, 2025 Ok so I know there is no good answer to this question but I just wanted to see if folks had any thoughts or suggestions. I have an older grizzly 6 inch jointer with HH that has dovetailed wings. It has survived two moves and all of my woodworking learning along the way from nothing to something. I know I still have lots to learn about WW and dream about getting an 8-inch parallelogram joint in the future, just have not saved up and trying to out a little in the tool cookie jar for some day. I seem to be able to mill square and flat boards from my rough lumber. At least I have not tracked a jointery or other project issues back to the milling. And usually that is more fighting something at the table saw when ripping or the actual joint construction. I always fight a little snipe out of my dewalt planer and the jointer, but usually leave my boards a little long to address that issue. I just rotated all of the knifes on the jointer and planer and they are running great. Is it worth checking to see if the wings on the jointer are still coplainer or would I see this in the boards I am milling to know there is an issue to address? I am kind of worried I will do more harm than good to the machine and my process. TBH I am scared to even unlock the infeed table to raise it up and check against the outfeed. Since they are DT style it appears there is not a whole lot you can do to adjust without heading down a very very long process that I am not sure will help and I might make it worse. And once my brain knows it’s off I will always keep that in the back of my mind when working. In the back of my mind this is why if I ever do get another jointer I would try and get the parallelogram, while the process still looks like it takes long it seems like it is actually more attainable for the average person to adjust the four bolts and not try to shim them or some other crazy method. 1 Quote
Popular Post Beechwood Chip Posted February 14, 2025 Popular Post Report Posted February 14, 2025 On 2/14/2025 at 12:02 PM, Woodworking_Hobby said: [...] I have not tracked a jointery or other project issues back to the milling. If it ain't broke, don't fix it 2 1 Quote
Popular Post gee-dub Posted February 14, 2025 Popular Post Report Posted February 14, 2025 There is more than one thread on here where someone started adjusting their jointer with no clear goal and ended up in a mess. Unless you’re seeking to resolve a specific problem I would leave well enough alone. JMHO 3 1 Quote
Chet Posted February 14, 2025 Report Posted February 14, 2025 What everyone said above. Having said that, snipe on the jointer is usually caused by the out feed table being a little low in reference to the blades on the cuter head. I had to go through this on my Powermatic when I changed from straight to a helical cutter head on my machine it wasn't necessarily difficult but sort of time consuming to get it dialed just right. 1 Quote
Woodworking_Hobby Posted February 14, 2025 Author Report Posted February 14, 2025 2 hours ago, gee-dub said: There is more than one thread on here where someone started adjusting their jointer with no clear goal and ended up in a mess. Unless you’re seeking to resolve a specific problem I would leave well enough alone. JMHO That’s what it seemed like from what I saw looking around online and felt like I would start chasing my tail. Thanks for the info! Quote
Woodworking_Hobby Posted February 14, 2025 Author Report Posted February 14, 2025 2 hours ago, Chet said: What everyone said above. Having said that, snipe on the jointer is usually caused by the out feed table being a little low in reference to the blades on the cuter head. I had to go through this on my Powermatic when I changed from straight to a helical cutter head on my machine it wasn't necessarily difficult but sort of time consuming to get it dialed just right. Thanks for the tip! I will take a look at that next time I am using the jointer to see if the table is a hair low or if I am just not putting pressure on the board correctly. It’s way more noticeable when I am edge jointing than when I am doing a face so it might be how I am putting downward pressure on the board. Quote
roughsawn Posted February 14, 2025 Report Posted February 14, 2025 When you are finishing your jointing cut...at the end...don't put pressure on the board right on top of the knives. keep the down pressure on the board ahead of the cutter head, and just let the board come across the knives. Putting down pressure at the end of the board as it comes across the knives will give you snipe at the end of your cut/board. 1 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.