Popular Post Ron Swanson Jr. Posted June 8, 2025 Popular Post Report Posted June 8, 2025 Howdy friends. I don't know that this is really worthy of a journal but it's provided some challenges along the way, so what the hey. This is the first project I've done *almost* entirely by hand. I did use the table saw for the bevel ends of each piece. This is a bench for my elderly parents entryway, for taking shoes on and off. I'm simply trying to replicate the aluminum foot stool here Went with 5/4 cherry, because in my reptilian brain, I thought that extra beef would be nice. I'm second guessing that choice now as 4/4 would've been just fine. Ohh well. Flattening and dimensioning done by hand. I guess like anything else, the more i do this, the less daunting it becomes. No one will ever confuse me with a master but o managed to get them pretty flat and true. I didn't take pictures of the cross cuts on the table saw, they were at 12°. The Dovetails are not true compound DTs, but they are also not at a right angle. I definitely underestimated how much of a difference this would make. The layout is essentially the same, but scribing the baseline in the face on the high side of the bevel was s challenge, as the bevel prevents my marking gauge from making contact. The other thing that has proved to be more challenging than i thought it would be is clearing the waste while maintaining the angle. I cut a few practice joints in scrap so at least had an idea of what was coming. I had to get a little creative in creating a setup to transfer the tails to the pin board as these pieces are a lot bigger than the small boxes i usually make. Again the small angle wasn't going down without a fight. And that's where it's at. Working on the pin boards right now. Hope this comes together in the end. ------ Pins are cut. I got one side seated after more fitting work than i would've liked. And I made a world class mistake by not labeling my pieces effectively, and cut chamfers on the visible side of the tails on one side. An easily preventable error if i had taken 2 seconds to label things correctly. 6 Quote
Von Posted June 8, 2025 Report Posted June 8, 2025 I appreciate the journaling, especially the angled dovetails! 1 Quote
wtnhighlander Posted June 8, 2025 Report Posted June 8, 2025 Sounds like a challenge, and looks like you are overcoming it! Looking forward to the finushed piece. Don't second-guess your material choice, I think that extra heft will provide a more 'custom' look. 1 Quote
Popular Post fcschoenthal Posted June 9, 2025 Popular Post Report Posted June 9, 2025 Rob Cosman's latest video was a small stool where he used angled dovetails and goes through the whole process well enough that even I can understand it. 4 Quote
Coop Posted June 9, 2025 Report Posted June 9, 2025 I think it looks darn good. Looking forward to following this. 1 Quote
Ron Swanson Jr. Posted June 9, 2025 Author Report Posted June 9, 2025 On 6/8/2025 at 9:21 PM, fcschoenthal said: Rob Cosman's latest video was a small stool where he used angled dovetails and goes through the whole process well enough that even I can understand it. Thanks, i will check this out! Quote
Popular Post Ron Swanson Jr. Posted June 11, 2025 Author Popular Post Report Posted June 11, 2025 Initial dry fit. I was able to minimize the mistake of tapering the wrong side of the tails by planing through them. This leaves some slightly proud pins but that's small potatoes to fix. I have some gaps to fill and additional fitting to do. Though i probably don't have to sweat it too much. My poor father is blind in one eye, and can't see out of the other one. 4 Quote
Popular Post Ron Swanson Jr. Posted June 11, 2025 Author Popular Post Report Posted June 11, 2025 On 6/8/2025 at 9:21 PM, fcschoenthal said: Rob Cosman's latest video was a small stool where he used angled dovetails and goes through the whole process well enough that even I can understand it. I just watched this. Lots of great stuff in here, and helpful. It's always humbling and inspiring for me to watch guys at that level work. Cosman's attention to the smallest of details is really impressive. I don't watch a lot of YouTube, but when i do my absolute favorite handtool woodworker to watch is Jim Kingshott. He's passed on now, and the YouTubes are just replays of his VHS(?) offerings, but he's very entertaining and educational to watch. Here's one on cutting dovetails 3 Quote
Popular Post Ron Swanson Jr. Posted June 18, 2025 Author Popular Post Report Posted June 18, 2025 Not much to add for additional steps. Got the joints dialed in a little bit and chamfered all edges. Ready for finishing this weekend. 3 Quote
Popular Post Ron Swanson Jr. Posted June 18, 2025 Author Popular Post Report Posted June 18, 2025 3 Quote
wtnhighlander Posted June 18, 2025 Report Posted June 18, 2025 Looks great! Very neat and clean lines. 1 Quote
Von Posted June 18, 2025 Report Posted June 18, 2025 Agreed. Nice clean joints and overall look. 1 Quote
Ron Swanson Jr. Posted June 18, 2025 Author Report Posted June 18, 2025 Thanks fellas, appreciate the kind words! Quote
Mark J Posted June 19, 2025 Report Posted June 19, 2025 I think it looks sharp, and the joints are well done. 1 Quote
fcschoenthal Posted June 19, 2025 Report Posted June 19, 2025 Yeah, I'd be proud to have that in my house. 1 Quote
Popular Post Ron Swanson Jr. Posted June 21, 2025 Author Popular Post Report Posted June 21, 2025 Final picture after finishing. 5 coats thinned shellac and paste wax. All done. 5 Quote
Ron Swanson Jr. Posted June 21, 2025 Author Report Posted June 21, 2025 On 6/21/2025 at 3:14 PM, Von said: Well done! Thanks @Von! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.