drvince g Posted June 20 Report Posted June 20 What is the best way to repair this gouge and have it look similar to the wood already there. the picture is on my phone but I can’t find the way to get it in here. Any help appreciated 2 Quote
wtnhighlander Posted June 21 Report Posted June 21 I believe you have to make two or 3 posts before picture uploads are allowed. Can you describe what caused the gouge? 2 Quote
drvince g Posted June 21 Author Report Posted June 21 It’s a veneered door panel. Something hit it and pushed a piece of the front panel in. It has a perfect right angle corner and pushed in. veneered furniture panel with a fairly deep gouge that has torn through the finish and possibly through part of the veneer. ChatGPT says I should use either mohawk epoxy stick or abatron woodepox or DAP plastic wood. any suggestions are appreciated 1 Quote
fcschoenthal Posted June 21 Report Posted June 21 Trying to judge the size by the trim pieces, that's pretty big. I would classify it more as a dent than a gouge, but either way, it's not going to be easy to fix. You'll have a hard time getting it to match using any of the fillers that ChatGPT is recommending. You also run the risk of having to sand the filler smooth and damaging the veneer around it. I'm not a furniture repair/renovation expert, but you might want to contact one to see what they have to say. 1 Quote
Von Posted June 21 Report Posted June 21 I would not be inclined to try a filler. Perhaps my lack of skill at tinting fillers, but I would have no confidence I could get a good match and any improvement in the appearance. I would be tempted to try the old damp towel and hot iron trick. Put a damp towel on the dent and apply a hot iron. Just for a few seconds and then slowly increase the time. The idea is as the wood absorbs the moisture it will expand and the dent will pop out. It won't get you a perfect fix, but might get you close enough to be acceptable. In case your finish is water soluble, try this on a hidden spot on the furniture first. 1 Quote
wtnhighlander Posted June 21 Report Posted June 21 Scale is hard to judge from the photo. Definitely seems like the veneer is torn through to a softer substrate beneath. The steam iron method might work to level it out, but may need an assist if it is as large as it looks. I would consider attaching a small hardwood block to the depressed portion with epoxy, so you can apply some tension along with the steam, to pull it back to level. Then shave the bock away with a sharp chisel, and rub some wood glue and sawdust into the cracks. It won't disappear, but should improve. If you are ambitious and artistic, the cracks can be disguised with an assortment of wood stains, applied with fine art brushes to mimic the wood grain. Difficult with such a light color, but not impossible. 1 Quote
drvince g Posted June 21 Author Report Posted June 21 so I was just told they are going to paint the door white and not try to match the dent. I guess that makes things easier in a sense but knowing that what filler is the best to accept the door being painted? here are some more pictures with sizes. thank you all for such quick response. It’s a veneered door panel. Something hit it and pushed a piece of the front panel in. It has a perfect right angle corner and pushed in. veneered furniture panel with a fairly deep gouge that has torn through the finish and possibly through part of the veneer. ChatGPT says I should use either mohawk epoxy stick or abatron woodepox or DAP plastic wood. any suggestions are appreciated Quote
wtnhighlander Posted June 21 Report Posted June 21 I would use Bond-O. There is a version made for wood, rather than auto body use. It is easy to smooth and takes paint well. 2 Quote
Popular Post Tpt life Posted June 22 Popular Post Report Posted June 22 In the past, I have done as follows. 1) Razor blade cut the defect loose from the door. 2) Glue backing ply to the inside of the “skin.” 3) Glue the patch back in. 4) Sand 5) Putty 6) Paint If paint is not wanted, then you at least have a solid skin to work with, and filling to match the color is greatly simplified. 3 Quote
dwilliam Posted July 14 Report Posted July 14 Without seeing the photo, it's hard to recommend the best repair. If you can upload it, we can suggest whether wood filler, colored wax, stain, or a touch-up marker will blend the gouge naturally. 1 1 Quote
Mark J Posted July 14 Report Posted July 14 4 hours ago, dwilliam said: Without seeing the photo, it's hard to recommend the best repair. There are 3 pictures posted. Aren't you able to see them? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.