Coop Posted September 1 Report Posted September 1 Is there a general rule of thumb in relations to the size of the bit if it isn’t specified on the bit or packing? 2 Quote
Popular Post wtnhighlander Posted September 1 Popular Post Report Posted September 1 The only "rule" I know is that increasing bit diameter demands decreasing rpm. I suppose you could use diameter * pi * rpm to determine linear speed of the cutting tips, and adjust rpm as diameter goes up, to keep the linear speed the same as a shank-size bit at full rpm. 3 Quote
Popular Post Ron Swanson Jr. Posted September 1 Popular Post Report Posted September 1 On 8/31/2026 at 8:57 PM, Coop said: Is there a general rule of thumb in relations to the size of the bit if it isn’t specified on the bit or packing? Anything under 1" in diameter I run at full speed. I really only dial the speed down for large diameter panel raising bits, which I haven't used in quite some time. 5 Quote
Popular Post gee-dub Posted September 1 Popular Post Report Posted September 1 I have this from some article which may help. It is a general 'map' if you will. I have found too slow gives poor results as much as too fast. I slow down for burn prone woods like cherry. The deeper the cut or the more complex the profile the slower I go to a point. It is always good to have a piece of like-species scrap around to test on before you go after your "real" parts. 7 Quote
Popular Post Von Posted September 1 Popular Post Report Posted September 1 I echo others on the size of the bit. I expect what you are cutting and feed rate also play a role. I enjoy watching machining videos and what I can tell they spend significant effort to figure out their "feeds and speeds" on the mill and lathe. While they have some rules of thumb, it seems like they often just have to experiment. 3 Quote
Popular Post wtnhighlander Posted September 2 Popular Post Report Posted September 2 Just as a reference: 1" diameter @ 24k rpm = 71.8 MPH 3" diameter @ 24k rpm = 214.2 MPH Spinning a 3" diameter bit at 24k rpm would have me (slightly) worried about the carbide slinging off from centrifugal force. 4 Quote
Popular Post Coop Posted September 2 Author Popular Post Report Posted September 2 Safety is my main concern, not so much of the burning of the wood necessarily. I was thinking of the mass of some of the bits, turning at those speeds. Some bits much more intimidating than others. 3 Quote
Popular Post gee-dub Posted September 2 Popular Post Report Posted September 2 On 9/1/2026 at 7:33 PM, Coop said: Safety is my main concern, not so much of the burning of the wood necessarily. I was thinking of the mass of some of the bits, turning at those speeds. Some bits much more intimidating than others. Amen brother. Anything over 1" needs to be used in a table IMHO. I have seen people spin big bits by hand but . . . a big no thank you from me. Bwaak, bwaak, bwaak. (Did I spell that chicken thing right?) ; ) 4 Quote
Mark J Posted September 2 Report Posted September 2 On 9/1/2026 at 6:50 AM, gee-dub said: 12 hours ago, wtnhighlander said: 3" diameter @ 24k rpm = 214.2 MPH So even dialing back to 12k RPM the bit is still going a hundred miles an hour. 2 Quote
Koolan Posted September 21 Report Posted September 21 Yes, generally the larger the router bit, the slower you want to run it. Small bits can usually be run at higher RPM, while larger diameter cutters need lower speeds because the cutting edge is traveling much faster at the same RPM. As a rough guide, I’d start around 18,000–20,000 RPM for small bits, 16,000–18,000 for medium bits, and around 12,000–16,000 for larger cutters, then adjust based on the manufacturer’s recommendations, the material, and how the cut sounds and feels. I wouldn’t rely on RPM alone though - feed rate and taking lighter passes make a big difference too. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.