fuzzypirate Posted October 18, 2011 Report Posted October 18, 2011 I am installing overhead pendant lights in an outdoor arbor and am working on fabricating the mounting boxes. The electrical box is going to be recessed into a 6"x6" piece of doug fir, with the metal canopy concealing the inside box. I need to bore a 4-1/8" whole into the 6x6. My ideal solution would be a forstner bit that exact size I can throw in my drill press. Has anyone seen a forstner bit either 4-1/8" or even just 4"? Thanks! Quote
rmac Posted October 18, 2011 Report Posted October 18, 2011 They make big Forstner bits like that, but they're crazy expensive and you'd be crazy to buy one just for what you're doing. Why not just draw a circle on your board and cut it out with a jigsaw? -- Russ Quote
Beechwood Chip Posted October 18, 2011 Report Posted October 18, 2011 Electricians use hole saws for circular boxes for ceiling lights. Quote
fuzzypirate Posted October 18, 2011 Author Report Posted October 18, 2011 Sorry, I should have mentioned that the whole can't go completely through. It can only be about 1-1/2" deep, so using a jigsaw seems like it won't work. Quote
BenMinshall Posted October 18, 2011 Report Posted October 18, 2011 I'd use a hole saw in the drill press to cut the circle, then chisel out the middle to make the cavity. The 4-1/8" size is pretty common in plumbing, so you should be able to pick one up for under $20. Quote
PaulMarcel Posted October 18, 2011 Report Posted October 18, 2011 instead of chiseling out the waste, maybe buy a 4 1/8" holesaw, cut it through MDF, use as a template with a guide bearing on a pattern bit; that solves the cleanout. If 4 1/8 isn't available, get a larger one and use an appropriate guide bushing you likely have already in your drawer. If there's going to be a metal flange, you may not need it too exact anyway; if that's the case, compass the circle and route by eye. 1 Quote
rmac Posted October 18, 2011 Report Posted October 18, 2011 Sorry, I should have mentioned that the whole can't go completely through. It can only be about 1-1/2" deep, so using a jigsaw seems like it won't work. Well then, it looks like what you want is the bottom half of one of Marc's keepsake boxes! This video: http://thewoodwhispe...h-for-keepsake/ shows how to dig a big round hole like you're talking about using smaller drill bits and a router. The interesting part is about 8-1/2 minutes in from the beginning. -- Russ Quote
rmac Posted October 18, 2011 Report Posted October 18, 2011 If there's going to be a metal flange, you may not need it too exact anyway; if that's the case, compass the circle and route by eye. Yeah. Or forget the hole saw and make the MDF template by drawing a circle, cutting it out with a jigsaw, and cleaning it up until it's nice and pretty. Then use that to guide the router instead of a store-bought template like Marc showed in the keepsake box video. -- Russ Quote
duckkisser Posted October 18, 2011 Report Posted October 18, 2011 dang it r mac i wanted to tell him that........once again a min to late Quote
rmac Posted October 18, 2011 Report Posted October 18, 2011 dang it r mac i wanted to tell him that........once again a min to late Duck, you gotta be quick! -- Russ Quote
duckkisser Posted October 19, 2011 Report Posted October 19, 2011 except when you are working on wood then you just hurt yourself cut my finger today on chisel because i was rushing and distracted. but seriously the router way is the way to go unless you don't mind spending big bucks on a tool you might use once in your life. Quote
Jfitz Posted October 19, 2011 Report Posted October 19, 2011 the roughter way is to go unless you don't mind spending big bucks on a tool you might use once in your life. +1 on the router with a template and pattern bit. Quote
dwacker Posted October 19, 2011 Report Posted October 19, 2011 I'd hog 95% of it out with a 1" forsner bit on the drill press, then use a rub collar and straight bit to finishit off. Don Quote
duckkisser Posted October 19, 2011 Report Posted October 19, 2011 dont use a 1" use a 1/8 bit that way you can get it perfect and put very little stress on router Quote
Beechwood Chip Posted October 19, 2011 Report Posted October 19, 2011 Just to offer a wacky alternative: use two pieces of wood, use a jig saw to cut the hole in one, then glue together to make your final thickness. Might also save money by buying thinner wood. 1 Quote
fuzzypirate Posted October 25, 2011 Author Report Posted October 25, 2011 Thanks for the ideas everyone. I am going to do some test on scrap wood this week/weekend and see what works best before moving onto the real wood. I appreciate all the ideas. Quote
TimV Posted October 26, 2011 Report Posted October 26, 2011 Can you laminate two boards together to get the thickness you want? Then you can use a hole saw all the way through one board that is 1-1/2" thick then glue a solid piece underneath that to get your final thickness. Quote
over40pirate Posted December 22, 2011 Report Posted December 22, 2011 I would use my circle cutting jig on my router. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.