Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

how much glue will we need to get for this?

Featured Replies

Realized this is probably going to use up quite a bit a glue. Don't want to be caught in the middle of a glue up with not enough.

You might get by with a quart but best to just grab a gallon and use it to keep a smaller container topped up between strips!

I got myself a gallon of Titebond Extend so I will have some left over and will not run out of time during the project glue-up. The Extend allows for a bit more time to get the top aligned as it is a slower setting version of their glue. I just don't want to feel pressed for time while gluing things up.

Realized this is probably going to use up quite a bit a glue. Don't want to be caught in the middle of a glue up with not enough.

The top will take as much glue as the rest of the project and I used about 1/4 and 2/5 of gallon on tops alone. I am using titebond type 1 because it is a little harder of a glue when dry. I turned the heat off in my shop while doing the glue and let it drop to about 52 degrees about an hour before glue. At this temp you should have about 15 to 20 minutes to safely get things together.

I hear Roo Glue is a very good glue. Some say as good as Titebond. A large custom furniture shop in our city uses Roo Glue exclusively including a lot of bent lamination. Roo Glue is also less expensive than Titebond glue.

The top will take as much glue as the rest of the project and I used about 1/4 and 2/5 of gallon on tops alone. I am using titebond type 1 because it is a little harder of a glue when dry. I turned the heat off in my shop while doing the glue and let it drop to about 52 degrees about an hour before glue. At this temp you should have about 15 to 20 minutes to safely get things together.

Be careful, Titebond does not set up properly below 50 degrees. My shop is unheated and I learned this the hard way.

Be careful, Titebond does not set up properly below 50 degrees. My shop is unheated and I learned this the hard way.

In my experience with titebond, I've no problems north of 40 degrees. I drop the temp to about 50 in my shop for only one hour before glue up. The wood still has some warmth internally and so does the glue. The surfaces are just a little cooler which gives me a little more open time. I don't like to have to glue up segments and then glue up slabs. I'd much rather have each slab glued up in one shot. We use titebond a lot on jobsites (type 1 and type 3) and I have had success in 40 degree weather. South of that mark and nothing but failure.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.