Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

help mounting pvc to a machine

Featured Replies

need to mount this pvc for dust collection on this scroll saw i want it like this as much as possible so that i can have full range of throat for cutting. anyone have any idea on a good way to mount this and not have it vibrate off?

DSCN0255_zpsfb7c244e.jpg

A quick and dirty idea would be to run a couple of hose clamps or big nylon cable ties around the back part of the scroll saw and the vertical section of PVC. If that works, done. If not, then look for a Plan B.

-- Russ

I would use a plywood clamp for the pipe near the back. Cut hole in the plywood to match the saw and the pipe, then cut it in half and screw or bolt it back together. Under the table I would epoxy a 3/4" x 1/2" thick rareearthmag et (or one from and old disk drive) to the end of the pipe and stick it to the underside of the table. You might could do the same for the top pipe.

BRuce

Where's that trusty duct-tape when you need it? If it's good enough for Apollo 13... :)

I also second the cable-tie idea.

  • Author

Hate to go buy big bag of cable ties when I need only 3 :( might go with hose clamps to really hold it tight. The part that is difficult is the top pipe it bounces so much it moves the whole rack. Need a idea for supporting it don't want to bolt anything to my machine but can't really figure how I can mount something to the top without interfering with the movement. Can't lower the top pipe because then I would not be able to move the hold down piece.

Duck, you could always put an eye-hook in the ceiling and hang the pipe with wire. That would get it away from the vibration and ....and here is the key word....it's cheap.

  • Author

wire wont realy work it would be too flimsy and move around too much nice thought though. maybe i can do something based off of that idea.

Bend a piece of electrical conduit into a arch and mount the ends to the saw. Use the upper part of the arch to hang the pipe with a few bungee cords(which will absorb the vibrations).

  • Author

went with just some zip ties put them all along the back and bottom pipe and then left the machine on for a half hour the top pipe vibrates but it didnt come lose and thats before i glue it in. might not even glue it together that way i can take it off easily if i need to cut something crazy. and with my 2.5 hp shp vac i had to put a screen on the pipe because not only does it suck up any dust but it also sucks up my wood :) i can honestly say that no dust is geting into my furnice from this machine. anyone know why they dont just built this into the machine to start with cant cost that much to run a hose along the sides of the machine like they do with the blower hose.

thinking of geting a small shop vac to hook onto my 1" sander and my bench grinder so i can pick up any metal shaving as they come off of my machines from sharpening and buffing the carving tools. dont know if i will or not since i dont know how much mess ill make from sharpening my knives and gouges. (and yes i know wood dust and sparking metal dont mix thought of riging up some kind of wet pan that the metal will drop into. we will see

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.